|
Ads
|
Views
|
Condition
|
Price
|
Distance
|
Date
|
|
I'm looking for a good Chevy 327 engine!
posted by TxKahuna
WANTED:
I'm looking for a good Chevy 327 engine in the San Antonio-Austin, Texas area!
Send photos and information!
magarner1982@g ...
|
96
|
None
|
n/a
|
|
April 8, 2013 14:06
|
|
|
TH400 HD
posted by smokinwoody
* TH400 HD just BUILT for sale...street/strip/ Chevy Bellhousing or use an adapter for BOP.
*short tail shaft (4")
*Alto Red Racing Clutches
*Kolene Racing Steels
*Kevlar ...
|
126
|
Excellent
|
$1,300.00
|
|
April 8, 2013 04:01
|
|
37 Ford Cabriolet Conv.Project
posted by ssaza
For sale is a 37 ford cabriolet Project. Has a Curry 9" rear. No brakes or center section. Has been narrowed and has a 4 bar rear set up.Frame has been reworked and totally bo ...
|
387
|
Good
|
$18,000.00
|
|
April 1, 2013 15:59
|
|
|
Complete Fast XFI fuel injection system with wiring for chevy
posted by darkostoj
I bought these for a project I was working on but ended up going a different route.
This was bought for a supercharged gen 1 chevy in a 67 camaro, but I ended up doing a ls ...
|
217
|
Excellent
|
$1,800.00
|
|
March 22, 2013 14:51
|
|
1957 CHEVY BELAIR 2 DR SEDAN
posted by firefly420
1957 Chevrolet Belair 2 door (NO POST) sedan, 4 speed, 350/350 engine, asking $23,500 OBO or trade for motorhome of equal value or cash/trade. Spent over $20K in 2011 for engi ...
|
473
|
Great
|
$23,500.00
|
|
March 20, 2013 12:55
|
|
Chevy 12 Bolt Posi Rear with 410 Gears
posted by shovel55
This will fit 67 to 69 Camaros,67 to 69 Pontiac Firebirds and 68 to 74 Chevy Novas.It may also fit others.This is ready to go you will need to use your drums.You have any ques ...
|
281
|
Great
|
$1,500.00
|
|
March 16, 2013 02:39
|
|
|
1955-59 Chevy Truck door vent window assemblies
posted by Moonhotrods
Needing the rt & lf vent window assemblies for 55-59 chevy truck. Good condition, muinimual rust, and rebuildable. Rubber, window felt, and glass are not important. Chrome can ...
|
158
|
None
|
n/a
|
|
March 12, 2013 11:29
|
|
1968 Pontiac 400 Complete bottom end build
posted by pontiacMAN1970
1968 Pontiac 400: casting number :9790071
Completely prepped
balanced bottom end
Bored .40 over
new clevlite bearings, cam, crank etc.
Keith Black hypereutectic pistons
...
|
259
|
Excellent
|
$2,200.00
|
|
March 11, 2013 10:26
|
|
69 Chevy C-10 SHOW TRUCK !
posted by 62cadd
This is a LWB 1969 c10. 383 stroker with a skat crank and rods low compression pistons and the cam is set up for the 177 WEIAND supercharger that's up top and it us all fed by ...
|
528
|
Excellent
|
$12,000.00
|
|
March 10, 2013 17:29
|
|
1954 Chevy Bel Air chopped custom project
posted by rod4314
Up for sale is a 1954 Chevy 2dr full on custom chopped rolling project. No motor or tranny. It has been chopped 8'' in the front and 10" in the rear with the back section lean ...
|
951
|
Fair
|
$5,000.00
|
|
March 6, 2013 16:32
|
|
|
FACTORY 59-60 CHEVY POWER BRAKE BOOSTER W/ MASTER CYLINDER
posted by 1959 chevy
FACTORY 59-60 CHEVY PASS CAR POWER BRAKE BOOSTER WITH MASTER CYLINDER, MAY FIT OTHER YEARS, NOT RUSTY OR PITTED, 100.00 OBO
|
155
|
Good
|
$100.00
|
|
March 5, 2013 13:25
|
|
|
59-60 CHEVY AT STEERING COLUMN W/ STEERING WHEEL, BISCAYNE AND EL CAMINO
posted by 1959 chevy
AT STEERING WHEEL FROM A 60 BISCAYNE OR ELCAMINO, STEERING WHEEL IS GOOD TO RESTORE,NO BAD CRACKS, COMPLETE WILL NOT SEPARATE.
|
169
|
Good
|
$150.00
|
|
March 5, 2013 13:19
|
Page 1 · 2 · 3 · 4 · 5 · 6 · 7 · 8 · 9 · 10 · 11 ... 16
|
|
