Hot Rod Forum : Hotrodders Bulletin Board

Hot Rod Forum : Hotrodders Bulletin Board (http://www.hotrodders.com/forum/)
-   Interior (http://www.hotrodders.com/forum/interior/)
-   -   I want custom seats in my 46 chevy truck (http://www.hotrodders.com/forum/i-want-custom-seats-my-46-chevy-truck-119837.html)

Countilaw 07-10-2007 12:36 AM

I want custom seats in my 46 chevy truck
 
I am Customizing a 46 Chevrolet pickup. I want to get rid of the bench seat and replace it with two bucket seats.

My question is, has any one done this before? And what kind of seats did you use?

The cab is not very wide so the seats will sit right next to each other.

Anyone have any suggestions?

Frank :welcome:

jalopy45 07-10-2007 09:14 AM

:pimp: Take a walk thru one of the U-Pull-it yards with your measuring tape and find something that will fit you and your truck. You'll want flat floor mounts so the mini-vans might be a good place to start. :thumbup:

Countilaw 07-10-2007 09:26 PM

Thanks, that's a big help. At least I have someplace to start.

Frank :welcome:

stea 07-17-2007 02:31 PM

I tried buckets in my 39 (same cab) and didn't like them. I ended up going with a 2002 Chrysler Limited mini van seat. Not sure if it is a middle or back seat but it fit perfectly. It was also covered in tan leather so there was no need to recover. I just stumbled on to this seat, most have an ugly side that is next to the body but this had both sides finished up.

46chevyfleetline 07-18-2007 07:46 AM

I believe the Ford Aerostar seats will work. Flat mounts and there is no flip down arm rest on the door sides. There is on the inside but can be removed.

horvath 07-20-2007 01:01 AM

That's the way -- measure the space you have and install what pleases you!

I want to do the same in my '54 Chevy pickup but I want low-back seats. I think I'll probably wind up modifying the seats I wind up getting but that's okay because I'll be recovering them anyway.

physcult 11-11-2007 04:07 PM

Quote:

Originally Posted by Countilaw
I am Customizing a 46 Chevrolet pickup. I want to get rid of the bench seat and replace it with two bucket seats.

My question is, has any one done this before? And what kind of seats did you use?

The cab is not very wide so the seats will sit right next to each other.

Anyone have any suggestions?

Frank :welcome:

Hi Frank
Im looking for seats for a 46, is your old bench for sale when you find some new seats?
Regards
Chris

302 Z28 11-11-2007 05:27 PM

If you can spare the $$$ one of the best, most comfortable seats on the market is made by Teas. They also have some premo buckets.

Vince

stitcher_guy 11-11-2007 08:54 PM

I'm not a fan of the Teas Designs or Glide Engineering seats. Just strike me as more frail and wimpy than an OEM seat out of something.

I had a customer with a 1940 Chevy and he had a pair of buckets out of a newer Monte Carlo (somewhere around 2000 or so). I pulled the headrests and redid the covers to make them more low-back.

A LOT of street rods (trucks too) have done quite nicely with Pontiac Fiero buckets. I was just measuring a set I have that I'm going to redo and install in a customer's 32 Ford roadster. He also has a Ford Ranger pickup that he's wanting to swap out the stock seats for something else. Those seats have a very very narrow footprint for the tracks, which would probably help you in fitting them in an older vehicle.

I have a set of seats from a Chevy Astro van that are very very nice as far as fit. They are very bolstered and sit deep and comfortable. They sit up on the pedestal piece for being in a van, but that also means you could use just the seat part, and adapt about any track set that you want, depending on how your floorpan is shaped.

I agree with the others. Just wander through the junkyard with tape measure in hand. Look for what seems to be a nice, full bucket and see how they sit. I like the buckets that are in Chevy Corsica (they don't flip forward) and Chevy Berreta (they flip forward because they were in a two-door) autos. They are a basic seat, with nice bolstering, that gives you a nice canvas to make whatever you want. And they're cheap.

I don't know what everyone else pays, but I get seats from my local wrecking yard for $25 apiece. I know the owner so I can even get full electric setups for the same, including the door switches and wiring harnesses. He usually lets me take the back bench pieces for free.

horvath 11-11-2007 11:28 PM

That was a good post, stitcher_guy ... I agree -- why spend $2000 when the wrecking yards are there? You can get some pretty sweet seats out of newer wrecks!


All times are GMT -6. The time now is 09:18 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.