Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
hotrodders.com: Project Journals: grapro's Journal
User Name
Password
lost password?   |   register now

View grapro's profile Entries: 212
Views: 115223
view from the beginning || now viewing most recent entries


Pages (43): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 [27] 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

12-21-2006 09:36 PM Channeled 3 1/2"
Finally got around to chanelling the truck dropped it 3.5 inches on the frame, going to leave the box the same. Leaving the box up it gives the chop that i'll do later even a meaner look from behind. Only problem now will be my rad has to be even shorter because of my 3 inch kickup to make it work, probly have to get a custom one made now.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #82]

12-10-2006 07:06 PM Motor Mockup
Just put the motor in and trying to figure out how high to mount it for clearance and whether I channel the body. Pretty tight and I gave it a extra three inches over a 32 frame. My firewall is very straight and I don't want to chop it up that much. Did a quick mock-up of the grill and the 4-71 i'm going to put on it. I've got a 327 375 hp I'll stick in later once it is redone. I think i'll channel it four inches throughout box and cab should look pretty mean going to chop it two inches also.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #81]

11-26-2006 09:22 PM 2 Bucks Worth
Here is a shot of my panhead bar I bought for 2 bucks and my wishbones cleaned up and ends welded in, Lookig for a different steering box everyone uses vega's and I would like to be different, any one have any Ideas? Another shot of my ladder bars and coil overs, just got everything tacked, I'll pull it all apart later and tig it up.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #80]

11-26-2006 09:15 PM Ladder Bars Installed
Just finished up installing the ladder bars and crossmember, used a hilti laser to get everything exact. Worked out fairly good, still have to make the panhead bar, got the heims and bar at a swap meet for 2 dollars if you can believe that, but i guess I got lucky.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #79]

11-19-2006 10:06 PM Ladder Bars
Nearly done the bars, made the ladders brackets and the rest, stiil have to finish off the crossmember and then mount them.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #78]

Pages (43): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 [27] 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43


All times are GMT -6. The time now is 09:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.