Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
hotrodders.com: Project Journals: Enigma10's Journal
User Name
Password
lost password?   |   register now

View Enigma10's profile Entries: 228
Views: 48272
view from the beginning || now viewing most recent entries


Pages (46): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 [44] 45 46

10-16-2005 11:51 PM 350 Chev
After a lot of thought purchased an Ali water pump and Delco HEI high performance 50,000 volt distributor with coil, this should keep the cylinders pumping in time. Still require an intake manifold and decent carburetor.


(click photo to enlarge)

(click photo to enlarge)
  [Entry #13]

09-22-2005 02:31 AM Front Spring
Got the front spring made from 1 ¾" by ¼" spring plate 4 leafs 26" long. Calculated I required approximately 400lb of continuous wait on the front end. Got the ends turned up as I am going to mount the spring above the axle so the axle ends up closer to the chassis.
This is required so I can use hydraulic shock absorbers. Bolted the spring in place used the engine lifter to lift up the chassis by the spring with motor and box in place. This compressed the spring as it would have if it was sitting on the ground. Tack welded the axle in place center to the spring.



(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #12]

09-22-2005 02:07 AM Perch Plates
Now that I have got the front cross spring manufactured its time to finish the perch bracket. I used 3/8" mild steel plate 4" wide, marked the pattern out using a hole punching machine I formed the curves. I then linished them together until they were smooth. Made the cross plate from 3/8" also, a-bit paranoid about strength and passing the vehicle certification. Tack welded and set it up center on the front round bar.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #11]

09-21-2005 11:55 PM Engine Mount
Joined the motor to the turbo 350 gearbox. Bolted the gearbox in place and set the motor up using the old manifold. Used an engineers level to make sure the carburetor would sit square and level. As my apprentice instructor always said may years ago tack first check double check wait a while check again then weld. I have decided to weld fully when I have nearly finished. It's a lot easier to remove something tacked than welded. After looking at the photo's I think I need to clean the shed up.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #10]

09-21-2005 11:40 PM Engine Mount
Decided to use 2" box section for the motor mounting tube. Auto-cad came in handy to get the correct cutting angles and total length of the bracket. Used a 6" drop for the engine support bracket. Welded fish-plates to the chassis. Setup the tube and engine mounts onto the motor before fully welding all the angles. The bracket shrunk by ½" after welding didn't think about this happening. I will need to add spacers between the fish-plates to prevent the chassis pulling in.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #9]

Pages (46): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 [44] 45 46


All times are GMT -6. The time now is 03:46 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.