Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
hotrodders.com: Project Journals: 1930u's Journal
User Name
Password
lost password?   |   register now

View 1930u's profile Entries: 219
Views: 71905
view from the beginning || now viewing most recent entries


Pages (44): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 [32] 33 34 35 36 37 38 39 40 41 42 43 44

03-16-2010 07:00 PM Detailing Front Axle
It's been some time since I last posted. Winter was bad and I got tired of heating the shop for hours just to prime a few pieces. The frame is done except for one last block sanding and then paint.

Most all the chassis sub assembles are all cleaned or rebuilt and ready for reassembly. Here's a few shots of the front axle. It's chromed out and drilled but I decided to add a little detail with some flat red paint. I plan to carry the flat red accent through out the car.

The new king pin bushings are in the spindles but I still need to ream and fit them to the pin. Thank you Speedway Motors for the excellent inexpensive kit!



(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #64]

12-05-2009 08:40 PM 1930U King Pins and Bushings
King Pins and Bushings

In an earlier post I mentioned that my spindles and king pins came apart nicely. Today I pressed out the bushings and cleaned up all the parts. No damage was found but the left side had just a little play in the bushings. Measuring found that the pins both held a consistent diameter of .811".



(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #63]

11-27-2009 07:23 PM Frame finish work
More work on the top of the frame today. I'm really spending a lot of time to smooth out frame horns and cradle. I figure since this area can all be seen I will try to make it look as good as possible. The roll bar plan is also coming together. Still not 100% on the roll bar but I found some PVC pipe to use for mocking up some different concepts.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #62]

11-26-2009 09:19 PM Frame top side and roll bar mounts
I flipped the frame over and started the finish work on the top. Before I finish the epoxy coat on the top I wanted to plan and layout the roll bar mounts. Here's a few shots.





(click photo to enlarge)

(click photo to enlarge)
  [Entry #61]

11-22-2009 07:47 PM Hiding the welds

I didn't get as much done today as I wanted to. I sanded all the spot putty areas and ground the top of the rails. I sealed the frame again and applied two coats of epoxy primer. It took less than a quart of primer to seal and coat the entire frame.

I'm also applying structural filler on all the weld areas. A few before and after pics.



(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #60]

Pages (44): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 [32] 33 34 35 36 37 38 39 40 41 42 43 44


All times are GMT -6. The time now is 09:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.