Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
hotrodders.com: Project Journals: jgb7038's Journal
User Name
Password
lost password?   |   register now

View jgb7038's profile Entries: 376
Views: 93760
view from the beginning || now viewing most recent entries


Pages (76): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 [35] 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

07-05-2010 09:01 PM Cab corners
After getting all the filler cleaned out I was able to finish welding up the cab corners.


(click photo to enlarge)

(click photo to enlarge)
  [Entry #206]

06-23-2010 09:29 PM Cleaning out some filler......
Was cleaning the lower cab corners so I could weld on them,and got alittle carried away.....ended up stripping the rest of the filler out of the cab.I had found some small rust bubbles where the seams from the top chop are.So I figured I better dig it all out now so I does not bite be in the butt later.I sanded on the doors for now,haven't seen any signs of rust but Im going to give them a VERY close inspection.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #205]

06-23-2010 09:24 PM Getting access
With the motor and trans out,I can get to the areas that where obstructed by the drive train.I put it back up on jack stands,so i cna get started on the underside of the cab corners.


(click photo to enlarge)

(click photo to enlarge)
  [Entry #204]

06-23-2010 09:20 PM Shifted gears...a little.....
I've been trying to get the welding/grinding finished on the cab.But like a few times in the past I had to do another part of the project to finish the one I'm working on.In this case,the motor/trans had to come out so I can finish the lower firewall/trans tunnel area.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #203]

06-19-2010 10:13 PM Filling more holes
Been trying to get all the cutting/welding done on the cab,filled a few unneeded holes in the doors and the jams,the last hole is a bolt hole for the latch.Cleaned up the rocker area and filled the open area at the base of the door hinges.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #202]

Pages (76): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 [35] 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76


All times are GMT -6. The time now is 06:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.