Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
hotrodders.com: Project Journals: jgb7038's Journal
User Name
Password
lost password?   |   register now

View jgb7038's profile Entries: 376
Views: 93781
view from the beginning || now viewing most recent entries


Pages (76): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 [50] 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

01-23-2010 08:12 PM Drivers door....
Made my way across the dash onto the drivers door. Unfortunatly the filler piece for this side was not quite in as good of shape as the other.So I made a filler piece to replace the bad spots.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #131]

01-10-2010 08:37 PM In with the column.....again
Put the column back in again. When it comes time for an interior,I will make the lower part of the column cover,most likley from chip board and fiberglass.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #130]

01-10-2010 08:33 PM Covering the column...
I ended up making a cylinder to fit around the column from the bottom.I welded some mount brackets to the under side of the dash to attach the cylinder. I made a small "hood" to the dash to cover the top part of the column.


(click photo to enlarge)

(click photo to enlarge)
  [Entry #129]

01-10-2010 08:27 PM Covering the column...
Finished up the couple of holes from yesterday. With the column back in the truck I decided I needed to make some kind of cover that would tie it into the dash. I mocked up some sheet metal to see how I wanted it to look.


(click photo to enlarge)

(click photo to enlarge)
  [Entry #128]

01-09-2010 08:32 PM Moving across the dash.....
I decided to weld up the few holes on the dash on my way over to the drivers door. Welded up some smaller trim holes,made the fillers for the heater control and old steering column holes. Still have a few more to weld up and then I can close up the drivers side of the dash like the passenger side and start on the door extension.


(click photo to enlarge)

(click photo to enlarge)
  [Entry #127]

Pages (76): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 [50] 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76


All times are GMT -6. The time now is 03:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.