Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
hotrodders.com: Project Journals: chief36chevy's Journal
User Name
Password
lost password?   |   register now

View chief36chevy's profile Entries: 284
Views: 44524
view from the beginning || now viewing most recent entries


Pages (57): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 [19] 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

03-30-2013 07:47 PM Cab rebuld cont.
I fabricated a small patch out of a piece of scrap. After cutting it to size I took a piece of pipe chucked it in a vise and used a hammer to form a radius in the patch. I then spot welded the patch to the inside of the cowl.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #194]

03-10-2013 05:31 PM Cab rebuld cont.
Im finally ready to strip it down and get it ready for paint. I bought a couple quarts of paint stripper one was a universal stripper and the other was an aviation paint stripper. The aviation stripper, although more expensive, works much better. I did need to open my garage door because of the fumes. So far so good I only found a few small spots of rust out that will need to be patched.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #193]

03-10-2013 05:28 PM Cab rebuld cont. Bearclaw Latches
Ok Back to the doors. I drilled some holes at both the bottom and top of where the latch plate will be located to weld the plates to the backside of the jam. It took a bitt of adjusting but both doors close and latch.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #192]

03-10-2013 05:26 PM Band saw oiler
After years of spending time sitting by my little band saw with an oilcan lubricating the blade I finally came up with an inexpensive way to lube the blade. I started with an old paint gun reservoir and taped the bottom with a pipe thread. Next I added a old sink hose to run it down to a magnetic base oiler nozzle. I then stole a cookie sheet from my wife (she doesnt bake many cookies anyway) I add some 3/8 pipe thread flanges and sandwiched the cookie sheet between them. The top flange I cut some slots in to allow the oil to flow through. I then drilled a hole through the center of the flanges and added a nipple to the bottom flange. I took a piece of Scotch brite pad cut a hole in the middle and secured it to the top flange as a chip filter. I pushed the piece of the hole down in the top flange to a point below as a secondary filter. I drilled a hole in the band saws shelf and placed the cookie sheet in the hole. I then placed a 1 quart oil bottle under the shelf with the nipple in side. I later added an IV pole to hang the reservoir. The operation is simple, just take the oil bottle out pour the oil into the reservoir and replace the bottle adjust the flow and start the saw.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #191]

03-10-2013 05:23 PM Cab rebuld cont. Bearclaw Latches
Ok Im ready to install the latch bolts. The first problem was that the flat part of my door jams were not as wide as my bearclaw latch blot plates so I needed to cut down the plates as well as the nuts inside. I clamped the plates in my bandsaw and cut about a off each side to make them fit. After I cut down the plates and bolts I took pieces of what I cut off and welded on each side to hold the nuts in place.


(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)

(click photo to enlarge)
  [Entry #190]

Pages (57): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 [19] 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57


All times are GMT -6. The time now is 05:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.