Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Tolerable compression without squish
User Name
Password
lost password?   |   register now

Thread: Tolerable compression without squish Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-19-2008 11:01 AM
spitnl Thanks for your reply Keith.

I have checked for pistons, the one I found are $700-$800 from Ross Pistons.
Having the heads and intake milled is about $200.
I will need custom pushrods anyway, with the original ones lifter-preload is 0.080 at this moment.

If you've got another source for the pistons I would be glad to hear.
I don't think it is possible to change the pistons with the engine in the car?

Frederick
09-19-2008 05:53 AM
k-star
quench

You will be fine..

Something to think about,,

Make sure you calculate the amount of mateial needed to reduce the chamber 14cc to get your compression of 9.5. The intake side of the head will also need cut, you will probably need another set of pushrods because of the shaft mount rockers. You will probably need to work the intake holes also. When you add all this up it may be a better deal to get the correct pistons.

If it's a fresh engine i would buy the pistons before i choped the heads/intake JMO.


Keith
09-18-2008 02:29 AM
spitnl Sorry Keith,

Chrysler 383 +0.030
440source aluminium heads 84cc
0.088 squish (pistons are 0.040 in the hole, 0.044 head gasket)
4000 lbs car
no towing
3.31 diff
4 speed manual transmission
Lunati 60302 cam
Intake:
Advertised duration: 262
Duration @0.050: 220
Lift: 0.475"
Exhaust
Advertised duration: 268
Duration @0.050: 226
Lift: 0.494"
Stock 1.5 stamped rockers
600 cfm Edelbrock #1405
Weiand stealth aluminium intake
1.75 headers
Static Compression is currently 8.5:1 but I would like to raise it to 9.5:1 by milling the heads.
I know it is best to raise the compression by buying custom pistons to lose the 0.040 in the hole, but engine is in the car now and the pistons are $$.
I cannot do a compression test because the heads are not yet on.

Frederick
09-17-2008 04:27 PM
k-star
quench

How about some details??

Engine type, CI

What is the static compression??

What heads?? iron or alum??

heavy car high gear, light car low gear???

towing 10,000 lbs????

ETC..


Keith
09-17-2008 04:05 PM
techinspector1 Just a wild-*** guess, but maybe 9.0-9.5 with iron heads?????
Depends on the cam also. A hotter cam with a later intake valve closing event will allow more compression before detonation. Have you done a compression test on the motor to determine cranking pressure?
09-17-2008 06:31 AM
spitnl
Tolerable compression without squish

I was wondering how much compression could you safely run on an engine without effective squish using 94 octane gasoline?

Frederick

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.