Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Replace bearings after crush or put them back where they came from?
User Name
Password
lost password?   |   register now

Thread: Replace bearings after crush or put them back where they came from? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-23-2009 01:04 PM
k-star
bearings

Here is my rule. If the bearings were installed and NOT heat cycled (engine started) i will re-use them. If the engine was started, even one dyno pull and i need to take it apart they get replaced.

In your case becasue of the dirt they need replaced. You also need to get a bottle brush and clean the oil holes in that crank. I have seen it many times where the grinder will take the crank out of the grinder, blow it off and bag it. Figuring the builder will clean it, the builder figures that the crank grinder cleaned it..

Keith
03-23-2009 12:14 PM
DaSouthWon I'm really not sure why they are scratched, but it is obviously from some foreign material that wasn't supposed to be there. All of the scratches resulted from the engine being turned over by hand after assembly. I pulled it apart because I was pretty certain that some sort of contamanent had entered in to the short block, and rather than risk it I figured it was definately worth the time to pull it apart and thoroughly clean it.
03-23-2009 12:09 PM
richard stewart 3rd Hi,
Reusing the bearings after them being torqued isn't a problem,
but why are the bearings scratched? was the engine cleaned?
was the assembly area clean? was he just careless?
I think I would have everything cleaned, & then use new bearings, just to be safe.
Rich
03-23-2009 11:58 AM
Plaintoast I'd spend the $50 and replace them, that way you won't be kept up at
night worrying whether or not they'll cause you any trouble.
03-23-2009 10:46 AM
DaSouthWon
Replace bearings after crush or put them back where they came from?

I have a 454 bbc that was put together buy a friend of mine but never cranked. To be safe I disassempled the short block to clean it since it had been sitting for a period of time uncovered. When I pulled the crank out I noticed scratches in all the bearings, a few deep enough to catch your fingernail on. The crank sat out after being disassembled and got some light surface rust on it so I took it and had the oil holes chamfered and the journals polished. The crank is well within spec for bearing tolerances, however I am unsure about using the unused bearings since the have been installed and tourqued down previously and have some light scratches, plus the crank has been polished. I realize that main bearings aren't that expensive but I don't want to throw them away if they're safe to use.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.