Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Car won't turn over! I'm stumped!
User Name
Password
lost password?   |   register now

Thread: Car won't turn over! I'm stumped! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-10-2002 06:04 PM
dmorris1200 Thanks for the update, it's always nice. I've been following the topic and knowing nothing about older Chryslers looked at it as a chance to learn something.
04-10-2002 04:51 PM
Bo_Jangles Thanks for all the help guys.

It turned out that the wire that was disconnected that went to the thing between the firewalland carb WAS the problem. the wire splits and one end goes the the oil pressure thing and the other on goes to the harness. I tried to start with and without it connected, and it was indeed that wire. It's amazing how a simple little ground wire can cause so much frustration!

Thanks again,
Beau
03-22-2002 08:59 AM
Bo_Jangles well, i got back under the thing and looked for any wires that might go to the neutral starting switch. I found one wire and put it on, but still nothing...

So I don't know. I'm going to hire a mechanic for $40 per hour to come over and help me. It better not take him longer than 2 hours. haha.

Beau
03-21-2002 09:50 AM
Bo_Jangles I added something to the page with the pictures. The neutral starting switch according to the shop manual has a wire that must be dissconnected in order to test it. Well the switch on my car doesn't have a wire on it.

So I'm guessing that might be the problem i'm having with the starting situation.

Any other MOPAR guys out there who might of been in this situation before?

Thanks for the help so far.

Beau
03-20-2002 09:17 PM
4 Jaw Chuck That thing between the tranny and carb is your oil pressure switch. I think your linkage is misadjusted and although the trans is in park the neutral start switch in the column thinks it is in gear. You could try disconnecting the trans linkage (make sure it's in park position!!!!) and then try starting the car with the shift lever in park and then neutral while moving the shift lever. My guess is your neutral start switch is shot or the linkage is out of adjustment, the switch is in the column behind the steering wheel. You will have to remove the wheel to access it. It ties into the ignition switch which sends power to the solenoid.
03-20-2002 10:00 AM
Bo_Jangles I checked the starter and it works. I looked and didn't see any wires at all that go from the tranny to the rest of the car. I took some pictures of the tranny linkage and engine bay:

<a href="http://www.geocities.com/bo_jhangles/problem.html" target="_blank">http://www.geocities.com/bo_jhangles/problem.html</a>

Hopefully, these pics will help you guys see what I see. Thanks for the help so far.

Beau
03-20-2002 09:16 AM
mustang66maniac The cable that is connected to the throtle is the kickdown cable. When you punch it when your cruising, the throttle will pull on that and cause the tranny to kick down a gear. It is possible that you could have hooked up your linkage wrong. I did that once, so i tried to start it in reverse instead of park. The nuetral safety swith wouldnt let me start it. So check that first. Also, it doesnt even look like a switch. On a ford it looks like sorta a mix between a crescent and a half circle, it has two wires on it that goes to the engine compartment. Hope i could help a little even though i have a ford.
03-19-2002 05:54 PM
1BAD80 There is a ballister resister on the fire wall.
Put a jumper wire accross it and see if it starts.
Its a white ceramic block, 1" X 3" with either 2 wires or 4,if they burn up it will turn over but not start / or not do anything. Hope this helps. Please give any feed back when you find the problem.LOL
03-18-2002 11:48 PM
BadBowTie I'm not sure, but I think the neutral saftey switch might be in the steering column, or at the base of the shifter if it's on the floor
03-18-2002 10:41 PM
Bo_Jangles On my trans all there is is the linkage that is connected the throttle and an actual lever which is what moves when you move the selector on the tree. I don't see anything that resembles a switch at all. could've the tranny been in a different gear than park or neutral when i hooked up the linkage? I know I had an automatic starter switch connected to the starter when I was bolting flex plate to the torque converter and it was turning over just fine...Hmmm...this is really frustrating...

I'll try to take a picture of the linkage tomorrow or the next day and post it here so you guys can see what i'm talking about and everything. Thanks for the info so far.

Beau

[ March 18, 2002: Message edited by: Bo_Jangles ]</p>
03-18-2002 07:52 PM
jimm beau, howdy!,DMORRISS is right on with his suggestion. the only other thing is you may have damaged connections to starter somehow.jimm
03-18-2002 11:24 AM
dmorris1200 If all you did was R&R the trans (nothing else) the first thing I would check would be the neutral safety switch. Fords are right on the trans shift linkage, not sure on Chrysler. On Fords you can diconnect the harness to the switch and run a jumper across the two wires for the neutral start circuit and try and start it. If it starts you know the switch is bad. Just a guess.
03-18-2002 09:16 AM
Bo_Jangles
Car won't turn over! I'm stumped!

Okay,

I just got done swapping the A-727-B transmission in my '66 Chrysler 300. I changed the filter and pan gasket and all that. everything is connected and the shift linkage seems fine.

But for some reason the car won't turn over when I turn the key now. Not even a "click". Nothing. I charged the battery all night, and tried it this morning, but nothing.

Does anyone have any ideas? I really want to get this car started. I've been working on this tranny swap for over a month. please if you have any suggestions i would really appreciate it.


Thanks,
Beau

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.