|07-24-2009 07:38 AM|
|Why J?||Schoust if you have a specific question I will do my best to answer but I'm new at this so I only know a little.|
|07-24-2009 02:44 AM|
give me a shout when you need too buddy
|07-23-2009 11:08 PM|
|mitmaks||Looks pretty good, I like the color. i would paint in my garage also but don't want neighbors to complain.|
|07-23-2009 06:33 PM|
|Schoust||Well I have been talking to other's about what to do and since I can't seem to get anyone to give me the right time the day I figure why the hell not! I am going to finish reassembling the car tape it off and go for it!!|
|07-23-2009 04:38 PM|
RELAX THATS THE KEY
move your body and the gun
just let the flow.......
|07-22-2009 11:37 AM|
|Why J?||JUst relax and take your time, also practice on a spare panel.|
|07-22-2009 11:33 AM|
|Schoust||Hey J thats pretty nice work there! I am also a Newbe that is attemting the very same thing and I am also relying on the Old Deadbodyman to help me through. All i can say if it comes out anything like your Jeep i will be very pleased! Nice Job!|
|07-20-2009 07:54 PM|
I'm going to wait a week before I try any wet sanding. I need a break. I have been working on this thing almost non stop for 3 months now.
I'm very happy with the paint. I was very surprised that I was able to get the metallic down with out splotchyness our tiger stripes.
|07-20-2009 07:15 PM|
Congrats, give yourself a pat on the back.
I would wear proper footware in the garage. Not only is it easy enough to drop something on your feet while working in a garage, when your spraying products, especially with isocyanates, you want all exposed skin covered. Besides isos being able to enter by breathing them in, The skin will absorb them, and they are attracted towards moisture (cover your eyes too) .
I like leveling most of the run by scraping with a razor blade. The method has been mentioned in past threads. And finish up leveling with a hard block. But you will want to allow those runs a chance to cure up a bit, or else you could tear off the clear at the heads of the runs if its still too soft.
|07-20-2009 07:03 PM|
good job ! Congratulations !
in any profession,business.... the difference between a Pro and an amateur....how well the mistake(s) are taken care of !
|07-20-2009 05:40 PM|
Knoxville LOL IM IN BLOODY SCOTLAND
Real nice job you have done there thats quite a tricky paint job for a novice
on the wet sanding the runs start with 1200 grit wet with a block and level the runs then with 1500 then 2000 grit and then start buffing
hope this helps
|07-20-2009 03:38 PM|
Nice paint job! I like the spray booth to!
Good to see somebody local on here to! (I'm from Clinton TN, not exactly Knoxville, but close enough )
|07-20-2009 01:42 PM|
Crappy cell phone pics that really don't do the shine justice.
But it passed inspection. The twins approve!
Proper foot gear is a must:
It will end up somewhere in this neighborhood just green and shinnyer:
It'a lot of custom work with alot of items from 3 decades of Jeeps all roled into one rig.
|07-20-2009 01:41 PM|
Only runs in the entire project: Whioch was the last item sprayed!
Door/hood: I'm happy
I haven't decided on what to do about the door. Color sand? block down and complewtly reshoot?
Also i have just alittle trash in the paint that fell after spraying, nothing terrible. I just need to buff it out.
If anyone has any tips on buffing out a little trash let me know. I was thingk sand with 1200 and then buff.
Thnaks every one again. Le t me know what you think.
|07-20-2009 01:40 PM|
Wanted to say THANK YOU, pics included.
I wanted to thank everyone that offerd a newbie some advice. You'all really saved me here, I spend months reading old post and in the knowledge base.
Wanted to specifically thank:
You guys really made my first paint job a true success. I can't thank you guys enough. If you guys are even in the Knoxville, Tn. area let me know I owe you a beer. I'll let the pics speak for them selves.
Not really a hot rod but my first entire vechicle painting:
When I got it:
Let the body work begin:
No pics of primer but we all know how that looks. so on to paint
My "spray both"