Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Building a 400 b drag engine, need some advise
User Name
Password
lost password?   |   register now

Thread: Building a 400 b drag engine, need some advise Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-31-2009 08:50 AM
Kmontgomery Sorry I should have been more specific. It is a Mopar Big block. 400 B.
08-29-2009 11:29 PM
ericnova72 !Bad and Stinger, read the OP's post, this is a 400 "B" engine = MOPAR, not a SBC.
08-29-2009 10:25 PM
stinger460 with a 400 get a good steel crank to start, 6" rods and a set of forged pistons to match, a hydraulic cam(w/ 1.5 rocker up to 600" lift no more than 245 deg of duration) with anti pump up lifters roller rockers with a set of heads complete with guide plates and all the trimmings, runners no smaller than 210 int" 75exh" an air gap makes a good mid range intake, use a good double roller timing chain with key ways for degreeing and if usuing a stock oil pan use a standard volume oil pump, dont go high volume with stock pan you can suck it dry.
08-29-2009 09:15 PM
1bad55 SBC's run very well with small chamber (64cc) and 2.05 intake valves and 1.60 exhaust valves. The porting of the runners is more critical. My 302 SBC powered '55 chevy runs 10.62 at 134 mph with factory double hump iron heads. And that was in the 1970's. Compression (around 13:1) and at least a .600 lift cam will make your power in a small block more than a set of $2000 heads. And remember - Small blocks when correctly built will run best in the 5000 to 8500 rpm range.
08-29-2009 06:42 PM
ericnova72 Have heard plenty of bad and not much good from the Mopar guys about Indy quality and customer service. New head from Predator is supposed to be excellent, the guy that makes them did all of the original developement work for the Indy group.
08-29-2009 06:32 PM
Kmontgomery
Building a 400 b drag engine, need some advise

Im have a 400 b. Id like to get 600hp to start out. I want to choose part that I can grow with. What do you guy's use. I looked at the Brodix b1 BS heads. And the indy ez-1 max wedge heads. I also looked at the Eagle 498 ci stroker kit. Any suggestion's advise ect ect......

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.