Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> what cambo is beast whith my 383
User Name
Password
lost password?   |   register now

Thread: what cambo is beast whith my 383 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-10-2009 12:46 PM
ap72 intended use is very important. 500hp in a street car is not as fun as it sounds. 500ftlbs doesn't mean much in a race car though... Look at where you'll spend 80% of your time and design for peak average power in that area.

a street car would be about 2,000-5,000 RPM. A race car would be about 5,000-7,000 RPM. You may be somewhere in between.
12-10-2009 12:23 PM
my87Z i've posted this on here before just recently but bare with me here i go again.

this is the motor i have in my 87 camaro:

350 4bolt main @ .040 over, decked .025, scat 9000 3.75 crank, KB 18cc D dished pistons, eagle SIR 5.7 rods, clevitte bearings, arp main, rod, and head bolts, pistons @ 0 deck, dart platinum stg 2 heads that have been cleaned up gasket matched and shaved to 60cc, solid cam with 282/290-240/250 @ .050 .560" adjusted lift from 1.6 roller rockers, victor intake angle and gasket matched with 1" spacer, 850cfm holley DP. compression is about 10.2:1

computer sim says 522hp/ 500tq

it's in a 3500lbs car, runs of high octane pump gas, newly built and i haven't really got the car completely tuned yet for the track but the last time at the track i was running 11.7-11.8 at around 116mph. i should have some faster times based on MPH, it should go 11.4-11.5 with some more tunning and practice.

not real sure if you are going to be able to get the 500hp mark out of the vortecs, i know it's been done, but you will need the perfect set up. with some port work the vortecs have been known to get around 240-250cfm @ .550" i think it would be a little more realistic to expect around 420-440 from the vortecs. but they do have excelent combustion chambers "fast burn" that are very affective.

what is the intended use for this vehicle, what is the vehicle, what kinda budget are you on, tire size and rear gear ratio would all be helpfull info
12-10-2009 11:02 AM
jarrettandroski those vortec if there 100 percent stock will take need some work to accept a cam with more then 465 lift or so, and if you want 500 hp most of your performance cams are going to have lift higher then that, i think you might have to get those vortecs ported to make that horsepower numbers to but im not to sure, what kind of car is the motor going in and what kind of gears do you got??
12-09-2009 03:20 PM
eloc431962 Welcome to the site.

Cole
12-08-2009 05:17 PM
wretched ratchet Welcome, Justin, I think if you will post this question in the "Engine Thread" you will get more responses - - - good to have you onboard.
12-08-2009 04:57 PM
bagoboy220
what cambo is best with my 383

hi my name is justin i need help i have a 383 sbc and im trying to get the most hp out of it i can at a cheap cost


i have cast iron vortec heads
950 holly 4 barrel
so far and have no clue from there
does anyone know a good combo to get close to 500 hp or more don't no much about cams and my heads but i do no thats where the power is

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.