Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> polishing tips
User Name
Password
lost password?   |   register now

Thread: polishing tips Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-10-2009 05:14 PM
ericnova72 Cartridge rolls(grit rolls, "tootsie" rolls) in 40-60-80 or 120 grit on a die grinder.I use 40 grit and 60 grit for aluminum, finer grits just plug up too easily and fast. You will need to get the mandrel for holding the cartridge rolls. Got to be careful not to hit the valve seats or slip and go "scribbling" across the deck surface or intake face. Watch out to make sure you don't hit the seat with the roll or with the grinder collet when you reach in deeper.

Get ahold of you local engine shop and see if they will sell you 2 old valves, an intake and an exhaust, and also grind them down so that they have no margin left. They may look at you funny until you explain why you want them LOL. You use these to drop-in and protect the valve seats while you are polishing the chambers, the current valves in the head will sit too high and you don't want to mess them up anyway.

In the ports, all you want to do is blend the casting and cutter lines smooth, anything more than that requires carbide cutters and a good deal of porting knowledge to not mess up the flow of a good head.

I've found the best deals on small amounts of cartridge rolls at www.competitionproducts.com . I would recommend you get 30 pcs 40 grit, 10-15 60 or 80 grit as they polish finer as they wear down, or just get the starter kit they offer as it has a little of everything and the mandrels. This is a good stop for engine related parts and tools.

This should be enough to get you started. I would highly recommend that you get a copy of David Vizard's book "How to Build Max Performance Small Block Chevy's on a Budget" , worth its weight in gold to a beginner, lots of pic's and good explanations.
12-10-2009 04:51 PM
79el camino
polishing tips

i have just purchased a set and trik flow heads and eldebrock airgap rpm intake. and i wanted to clean up the intake runners a little bit to get a little better flow. i was just wondering if there were any special techniuqies that had to be followed.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.