Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> SBC Comp Cams valve spring, pushrod, break-in questions
User Name
Password
lost password?   |   register now

Thread: SBC Comp Cams valve spring, pushrod, break-in questions Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-17-2010 07:10 AM
cobalt327
Quote:
Originally Posted by dlisabeth
The World Products SR torquer heads that I am using have dual springs on them.
No telling what they are, actually- w/o having them checked for pressure. According to SUMMIT, the S/R Torquers come w/single springs, no damper, w/lift good to 0.560".

Quote:
Are the springs that came in the kit intended to replace my current outer springs while reusing the old inner spring.
Just use the Comp Cams kit springs- as supplied- like DV said.

Quote:
Is installing the Comp Cam springs and seals something that I can do at home with a simple valve spring compressor?
Yes, it is easily done by you if you have a spring compressor. Be sure that you check each individual spring installed height before installing the springs, and shim if needed. There should be specs for the installed height w/the springs.

Quote:
Finally, I had my block zero decked to a set of speed pro flat top pistons. I am going to be using a .039 thick head gasket and stock rocker arms, will stock length pushrods work with this setup?
Always check for the correct p-rod length. There are too many variables to say the OEM length will be correct.
05-17-2010 02:38 AM
DoubleVision You don`t reuse old springs, you only use the springs that came with the cam. The cam you have is on the small side and won`t require a weaker spring to do break in procedure. Cam break in with weaker springs is only needed when your sure enough trying to break in a cam that`s huge and has mammoth sized springs on it. What happens is, the spring pressure on heavy duty springs is so high, it forces the oil wedge off the cam which ruins it.
Since the block is zero decked, your going to have to check valve train geometry after it`s assembled to know what lenth push rods to get.
If it were I, I would use a .041 thickness gasket with a zero deck.
After you get your valve train set up, make sure you break it in with lube that has ZDDP in it or the cam will go flat. The Valvoline race oil has it and works well for cam break in. You`ll have to keep using it there after to make sure the cam survives.
05-17-2010 12:56 AM
dlisabeth
SBC Comp Cams valve spring, pushrod, break-in questions

I am building a sbc which I will be installing a Comp Cams XE262 cam in. I bought the kit that includes the cam, lifters, valve springs, valve seals, and timing chain. The kit came with single valve springs. The World Products SR torquer heads that I am using have dual springs on them. Are the springs that came in the kit intended to replace my current outer springs while reusing the old inner spring. I have read that I should remove the inner spring for break-in, correct? Is installing the Comp Cam springs and seals something that I can do at home with a simple valve spring compressor? Finally, I had my block zero decked to a set of speed pro flat top pistons. I am going to be using a .039 thick head gasket and stock rocker arms, will stock length pushrods work with this setup?

Thanks,

Derek

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.