Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> reduce universal clear?
User Name
Password
lost password?   |   register now

Thread: reduce universal clear? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-27-2010 01:43 PM
daves66valiant On my flowcoats I reduce SPI universal about 10% to get it really flat and slick. Helps a little with urethane wave too as it flows out real nice. Unreduced flows really good too. Make sure you're using a 1.4 tip. It can be donw with a 1.3 but not recommended by Barry at SPI.
05-25-2010 07:00 PM
kenseth17 I have. Somewhere between 10 and 15 percent seemed to be the sweet spot if I can remember right on the last thing I painted, where it would start laying down smooth as glass and orange peel free (Not that it layed down all that bad unreduced, but a little reduction really improved it and the ease for me), and not run all over the place if I can remember correctly. But everyones different, setups and conditions are different. So experiment and find out what works for you.

I see no real problem reducing paint or clear, even if not called for and the amount is done within reason. Use a good quality reducer and allow good flash times.

Still going to be as good of a clear. Those solvents will evaporate back out and are not a part of the paint film and your left with the same plastic as if you had not reduced it. Just your mil thickness per coat will likely be less. As long as you apply enough mil thickness, or leave enough after buffing, your just fine. Should be no problem if you put on two or more coats, and don't take too much off cutting and buffing afterwards. The ratio of hardener to clear on the other hand should not be messed with.
05-25-2010 06:54 PM
panelwagon62 Well I guess everyone is different, I just wasn't sure if reducing it would make it any less of a good clear then it already is.
05-25-2010 01:14 PM
jcclark I don't reduce it when it's cold, but when it's hot I always reduce
it 10%, sometimes more when I'm doing a bumper and don't want to
buff it. I can get it real slick that way.
I can't tell a difference with less than 10% reduction.
It all depends on the gun and tip size too.
Once, by mistake, I reduced it 30%.
And it did fine, was slick and didn't die back or shrink.
I was impressed.
05-25-2010 09:33 AM
panelwagon62 Actually I used it for the first time over The weekend and loved it. Someone I work with asked as he always reduces his clears and I figured since I couldn't give him a straight answer I would ask someone here.
05-25-2010 09:22 AM
OneMoreTime You can..i would not go beyond 5% reduction..the question is why?? Universal clear lays out soo nice as it is if the gun is adjusted correctly..

Sam
05-25-2010 08:54 AM
panelwagon62
reduce universal clear?

Can you reduce spi universal clear?? If not why not?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.