Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Best tire PSI for street radial tires?
User Name
lost password?   |   register now

Thread: Best tire PSI for street radial tires? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-18-2010 08:59 AM
cucumber1949 The way that seems to work best for me is that when I have the car up on the 4-post lift, I raise the lift to bring the tires up to my eye level, get behind the rears and look for the full width of the tread to contact the lift ramp. I deflate the tires a little, and then slowly inflate them a step at a time until the sides want to lift off the ramp, take out a pound and call it done. Remember, as you start to drive the vehicle, the pressure will rise slightly due to the tire warming up. This works out to be 14-15 lbs on the rear of my T, 26 lbs for the fronts. When I had the super wides on the back, it was 9 lbs. My tires wear evenly and the car handles well. Of course you don't need a lift to do this, but I'm getting older and stiffer LOL, and my car has yet to be driven through any water, intentionally or otherwise :-)
07-18-2010 08:30 AM
sqzbox On low pro tires, look at the max pressure rating and start at 5-6 lbs less that the max rating. You have to consider tire temp as pressure will rise when hot and decrease when cold. Ride quality will also be effected by pressure. Some have even gone to nitrogen gas to keep pressure even at all temps. Nitrogen also works on air shocks and air ride suspension.
When you do the wet tire test, do it cold and hot and check for any difference.
This will show you the best over all pressure to run or if you got it right.
07-18-2010 05:24 AM
Ford Junkie Same test for traction. Unlessss your doing a burnout before hand if so then you'll have to drop the pressure some as it will increase with heat from the burn out.

You don't want hte rolled edge sitting on the pavement very much maybe 1/4" or so.
07-17-2010 11:54 PM
elano Dang. Well what would be the best PSI for traction then? lower or higher?

Also when I roll through the water, do I want to look at the wetness of the tire tread or the print it leaves? Also how far to the edge of the tread do I want? The tread seems to kind of taper off on the edges.
07-17-2010 07:59 PM
Ford Junkie tread wear is not going to be good with 11 1/2"s of tire on an 8 in wheel if my conversion of 295 width to 11 1/2 in. is correct. Looks good but wear suffers greatly, I have worn several sets out this way and they refuse to wear even as the sidewall wants to straighten at highway speeds which makes the center of the tire carry the load.

tire psi will have to be determined by how heavy the vehicle is. No real way to figure this other than the contact patch on the pavement. Run it through some water as stated to make sure all of the tread pattern is evenly hitting the road.

07-17-2010 07:07 PM
72highboy390 32 psi will be good
07-17-2010 06:49 PM
Best tire PSI for street radial tires?

I just mounted some pretty wide bfg 295/50/16s on a pair of 16x8 wheels. What's the method for figuring out the corect psi? For even tread wear more than traction I suppose. A friend told me to pull through some water and look at the patch but I'm not really sure what to look for. Had 30psi in them, now 27 and not really sure if I should go lower. MAX psi on them is 35.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 02:05 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.