Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> MSD 8981 programmer
User Name
lost password?   |   register now

Thread: MSD 8981 programmer Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-03-2010 03:04 PM
Greg T
Originally Posted by Overdriv
Go here for the manual for the 8981.

Thanx. I couldn't find that. All I could find on the site was the 8980.
09-03-2010 02:36 PM
Overdriv Go here for the manual for the 8981.
09-03-2010 12:27 PM
Greg T Okay, great. Thanx much. I do have an adjustable can on my pro billet and a limiter plate set to 12*
09-03-2010 12:17 PM
bubbahotep Ported would be better because it's not advanced at idle and you'd have an easier time picking an advance canister. It'll advance under load giving you over 36' (50' for example).

If you use manifold vac you'd be good with an adjustable vac canister. Turn in the adjusting rod to tighten the spring so it Doesnt advance at idle.

Either way you might get some pinging under load which means the vac advance is too much. That's always trial and error
09-03-2010 10:24 AM
Greg T Okay. Think I got ya. Lockout the mech on my pro billet and use the computer to manage it. I did not quite understand about the vac. Should I run full manifold advance at idle? Or does it want ported?
09-03-2010 09:55 AM
bubbahotep I've had that thing in my ride for nearly 20 years and have messed with it hundreds of times

you can use vac advance for better mileage but NOT to correct for a better idle timing. Meaning, some guys use the manifold vacuum to increase their idle timing. The 8981 screws up if you do that so just use vacuum advance on manifold but have it only come in off idle under load as intended

It will work with weights but it's not the best way. Locking out the advance at total (36-38 etc) will give perfect results always. I used it with weights fir a few years and had mixed timing because the computer is limited by what the weights allow it to do

works like this: you have 3 dials, idle timing, rpm to begin advancing, slope

the computer dials use your locked out timing as a maximum setting. 36' locked means it knows it can only give you 36' advance. If you adjust the idle dial to say 16'.....the computer drops 20' from 36 total.

If you use weights and the computer together: let's say the weights are partially out to 30' advance. The computer still wants to deduct 20' from whatever the total is so you now only have 10' idle timing. Only when you are at WOT will the computer give you precise timing

I have it locked 38' for my 383 stroker with aluminum heads. 28' idle setting gives me a nice rpm in gear. The computer gives 20' starting retard so starts are easy.

My only F-up was that my rotor phasing was way way off and I had hard starts when hot. People on this board pointed me in the right direction

it works with all msd boxes I think. It basically goes in series with existing msd wiring like a switch. Easy hookup, a few wires not including the high speed rpm retard option for boost
09-03-2010 09:45 AM
Greg T I sent him a PM. Thanx for the tip. It sounds like just the thing I need but even the MSD site doesn't answer my questions. And the tech support wanted me to hold for 20 minutes.
09-03-2010 09:24 AM
SSedan64 Check with Bubbahotep, his post in the TunnelRam thread said he uses one.
09-03-2010 08:56 AM
Greg T
MSD 8981 programmer

Howdy folks! Just wondering if someone has any info/experience with the 8981 timing computer. My questions are this: Does that work with a 6AL box or right off the distributor? Also, must one lock out the mechanical advance in the dist to use one of these? And, what about the vacuum advance? Thanx much!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:44 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.