Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Power seats
User Name
Password
lost password?   |   register now

Thread: Power seats Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-22-2010 08:05 PM
pnt4u2
Memory

Thanks for the redirect to Electrical. I will do better in the future. Thanks for the advice on controls. Both seats have "little black boxes" under them. I will try to locate schematic to wire a jumper. Keep on posting!
pnt4u2
10-22-2010 03:21 PM
vicrod The attached drawing shows a typical power seat wiring schematic.
Notice the three motors are powered to rotate forward or reverse depending on the desired function. The relays simply reverse the electrical polarity to reverse the motor.
The drawing shows a pair of relays for each motor controlled by single pole double throw center off momentary (SPDT) switch.
Switches can be used in place of the relays but need to be rated at least 15 amps and they would be double pole double throw center off momentary (DPDT).

vicrod
10-22-2010 10:08 AM
evolvo pnt4u2,
You didn't mention if your seats have the memory function but from how you describe the situation I'd suspect that's what's up.
I had a similar situation when I bought a set of 2006 Porsche 911 seats. The issue on the driver seat was that it had a memory function so you could preset seat positions for up to three different drivers. I found a plastic box with a circuit board panel mounted under the drivers seat. What I figured out was that this box communicated with a body control module which I of course didn't have, or want!
I got lucky though. I took the seat to the local Porsche shop where I found a guy who was into hot rods. He took the time to pull out the wiring diagram and sort out how to jumper around the circuit board so the seat worked like the pass side.
Hope this helps.
Good Luck
10-22-2010 07:08 AM
DanTwoLakes Yes, let's move this to the Electrical forum. You'll get better answers there.

Dan
10-21-2010 08:39 PM
Coodeville I think this is more of an electrical question than an interior fabrication question.
10-21-2010 08:34 PM
pnt4u2
Power seats

Bench testing 2006 Envoy front power seats prior to installation in cruiser. Passenger seat works fine when "wired" to temp power source via the 12 ga. orange and black leads. The Driver's seat does not work with same wiring. Is there any jumper or special "safety" needed to be wired prior to seat working? All I want is basic forward/back, tilt etc. Any advice?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.