Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> A Little Help with Stance and Tire Size on my V8 Bug Please
User Name
lost password?   |   register now

Thread: A Little Help with Stance and Tire Size on my V8 Bug Please Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-01-2010 06:27 PM
raidmagic Stance? You can't get any better than this!

Check out the build thread here. Lots of reading but an amazing car.
10-26-2010 07:53 PM
A Little Help with Stance and Tire Size on my V8 Bug Please

Hello Everyone as some of you guys know I have been building a V8 convertible 69 bug on an s10 chassis. I've recently finished rebuilding the front end of the chassis and think my next step needs to be figuring out the stance that I want to have so I can get the engine level, make up a trans. cross member, etc......

Here is the car as it sits right now. When rebuilding the chassis I put on 2" drop spindles, and the rear got dropped a little too with with shorter springs.

Right now both the chassis and body are pretty much level. The body needs to move forward a bit, but right now its hitting in the old rusted in s10 body mounts.... If I want the car to sit level I think I'll need to drop the body a bit more to close up the rear wheel well gap. I don't want to drop the body on the frame to much because I'm 6'3" and I don't want to have my head stick out above the windshield.... LOL

Here is a drawing showing what I think its going to look like when its done If I leave it sitting level.

Now it doesn't look bad, but I just think it needs a bit of a rake to it to make it look real nice. I could close up the front wheel well gap a bit and open the rear gap up a bit and get a little rake on the body, but I'm not sure that would be enough, and with the same size tires on front and back I'm thinking it also might look a bit off?????

So I messed with the drawing a bit and with larger tires on the rear end and a little bit of a rake to it I think it looks much nicer, maybe a little more aggressive?

So now If I'm going to be messing with tire size its going to make a difference in the hight of my trans cross member to get the engine level. I don't have the money to buy new wheels and tires right now but I need to figure out what size tires I'm going to want to use so I can move on....

Right now it has p21565r15 tires (about 25.5" tall) on front and back(from the s10), I have room to go wider on the back end, plus I'll be going taller, and on the front I figured I'd go narrower and maybe a tad shorter???

Is there a list of common tire sizes out there so I can pick something common and mock it up from that???

Lets start with the rear tire size, what width, and hight would be best, I'm planning on the car being a cruiser, no racing. Right now its just a stock 350 so not a whole lot of power yet, but I'd like to build an engine for it later, but probably only around 350hp.

What would be a good size tire for a cruiser with 350hp, 200r4 trans, and 3.42 rear end (rear end may change later when I upgrade?) 2500-2800lbs car, and I'll probably make some caltracs and put on the rear end.

How about front tires can I go shorter, and how narrow???

Any disadvantages to going with different size tires in front and back???? Well besides shorter life because I can't rotate them.

Any reasons I should stick with the same size tires front and back???

Thanks for all the help guys!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 01:18 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.