Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Installing a 56 dynaflow in a 54 Roadmaster
User Name
Password
lost password?   |   register now

Thread: Installing a 56 dynaflow in a 54 Roadmaster Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-25-2011 07:42 AM
gail smith from experience, ithink 264-322 bellhousing larger diameter than later engins and torque tubes longer or frame stretch change after 1955.better measure first to be sure. i have always wanted to try 264/322 iron bellhousing and probably torque conv on later dynaflows to see if everything links up ok. 61--63 are my favorites because still had dynaflow with open driveshaft.
04-24-2011 02:06 PM
Highball
56 Dyna Flow into a '54 Buick

I was a GM tech for ten years and the Dynaflow transmissions from late 1953 (first Buick V8) through to 1958 were almost all the same automatic transmission. There were some internal improvements but the bolt patterns and mounts are all compatible UNTIL you get to a Biuck Hearse, Limosene or Ambulance. Whether it was a 266, 322 or 364 the cases are the same.
Normbc9
04-17-2011 07:38 AM
gail smith
dynaflow doctor

helped a friend put a 1956 super engine/trans into a 1955 centurty once. the torque tube seemed about an inch too long-but it fit anyway. longer probably longer due to wheelbase difference.
11-28-2010 09:37 PM
sedan delivery
dynaflow

here is some information i found-- hope it helps


http://forums.aaca.org/f120/1953-195...on-274923.html
11-25-2010 05:46 PM
texasfats
Installing a 56 dynaflow in a 54 Roadmaster

I need help and advice on an installation I would like to make. I just purchased a 1956 Buick 322 nailhead for my car. Also I have a 56 dynaflow trans I can purchase if I can find out if it will work for my application. I want to up grade my 1954 Buick roadmaster. Can I do it, please break it down for me in detail? Thank you for your help in advance. I would like to get this completed during the Christmas holidays. Thanks again, Texasfats
I appreciate any and all help and advice.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.