Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Rebuilt 700R4 sat to long?
User Name
Password
lost password?   |   register now

Thread: Rebuilt 700R4 sat to long? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-11-2011 06:57 AM
daoldbuick Thanks for the replys. tnsmith - so far I haven't seen 3rd or OD but I haven't had a chance to drive it much yet. Took it down to the alignment shop this morning, so hopefully later today or tomorrow I'll get a chance to drive it. Will try what you said tnsmith and let you know. Im hopping it's simple like Overdriv says. Thanks
05-10-2011 09:53 PM
Overdriv If I were you I'd drive it a bit more before you do anything major. I rebuilt a 700R4 and let it set 7 years. It wouldn't shift out of 1st the first few times I drove it. I was just about to pull it and find out ***. I went to get it at the alignment shop and the guy said it shifted OK for him. It has worked perfect ever since.
05-10-2011 08:58 PM
tnsmith10
Quote:
Originally Posted by daoldbuick
Got a 700R4 3 years ago and had it completely rebuilt. Needed it that time to fab rear crossmember for it, put hole in flooring in the right place for the shifter etc, etc.. Finally last fall, the motor was in so put oil in the trans and started the motor and got it out for a test drive. Parking lot was to small to get it out of first. This spring I drove car to glass shop, and it shifted from first to 2'nd but not 3'rd. Had engine RPM up to 2700 but still no 3'rd. I'm concerned that sitting for so long without oil, one of those little check balls or something else has stuck. Anyone got any ideas on what might be wrong and easiest way to fix it? F.W.I.T. the motor is a ramjet 350, and there in a 36 Buick. The TV cable has been set and checked. I'd ask the guy who rebuilt the trans but he is retired and in another city so I have no way of getting in touch with him. Any help or ideas would be appreciated. Thanks.
so, from what i read here, does the trans also not have 4th(o.d.) as well as no 3rd gear? if that be the case, the first thing i would check is the 2-3 accumulator capsule that goes in behind the 2-4 servo and make sure that its there, which you either have to pull the servo assembly out or drop the valve body to see if its there. then also the simple fact that if it is, and was not changed could also be the problem as well, as they should be changed on rebuild. reply back on if you have 4th gear ( make sure its o.d. your feeling if you think it does and not the t.c.c. engaging as its quite common for people to get the 2 applications mixed up.)
if you do think it has 4th gear, when it engages, pull the trans to 3rd and see if it tries to down shift, if not, thats t.c.c. apply, and not 4th gear. t.c.c. apply is possible in 2nd gear so you know.
the last time i saw this, the builder forgot to put the 2-3 accumulator capsule in.
it could also be in the valve body as in time, its not out of the question depending on how bad the trans was tore up before the rebuild. the valve body may have sticky shift valve/s.
its not likely that it will be govenor related as if it was, more than likely you wouldnt even get a 1-2 shift. hope this helps...
05-10-2011 02:24 PM
daoldbuick
Rebuilt 700R4 sat to long?

Got a 700R4 3 years ago and had it completely rebuilt. Needed it that time to fab rear crossmember for it, put hole in flooring in the right place for the shifter etc, etc.. Finally last fall, the motor was in so put oil in the trans and started the motor and got it out for a test drive. Parking lot was to small to get it out of first. This spring I drove car to glass shop, and it shifted from first to 2'nd but not 3'rd. Had engine RPM up to 2700 but still no 3'rd. I'm concerned that sitting for so long without oil, one of those little check balls or something else has stuck. Anyone got any ideas on what might be wrong and easiest way to fix it? F.W.I.T. the motor is a ramjet 350, and there in a 36 Buick. The TV cable has been set and checked. I'd ask the guy who rebuilt the trans but he is retired and in another city so I have no way of getting in touch with him. Any help or ideas would be appreciated. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.