Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Master cyinder losing fluid from cover
User Name
Password
lost password?   |   register now

Thread: Master cyinder losing fluid from cover Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-17-2011 03:51 PM
adantessr
Quote:
Originally Posted by Fat 48
I replaced the master cylinder and so far there's been no more fluid overflowing from the rear reservoir. Thanks to all for their comments and suggestions!
Glad you got it fixed. :-)
06-17-2011 12:58 PM
Fat 48 I replaced the master cylinder and so far there's been no more fluid overflowing from the rear reservoir. Thanks to all for their comments and suggestions!
06-11-2011 11:34 AM
Fat 48 I dropped the fluid level in both reservoirs. Every time it overflowed, I took the lid off and both reservoirs were approximately at the same level as before and it did not appear as though one reservoir was gaining fluid at the expense of the other.
06-11-2011 08:15 AM
joe_padavano
Quote:
Originally Posted by Fat 48
I dropped the fluid level but it still overflows. I had a friend depress the brake pedal while I watched the master cylinder with the lid off and it was like Old Faithful! Brake fluid was shooting up out of both reservoirs. Is that normal? Still not clear to me how it's getting past the gasket. I guess I'll try a new M/C and see if that clears it up.
Let's ask the question again. You dropped the fluid level. When it started to overflow, was the level HIGHER than when you started? Was it in both reservoirs or just one? Was the other one lower than when you started?
06-10-2011 07:03 PM
Fat 48 I dropped the fluid level but it still overflows. I had a friend depress the brake pedal while I watched the master cylinder with the lid off and it was like Old Faithful! Brake fluid was shooting up out of both reservoirs. Is that normal? Still not clear to me how it's getting past the gasket. I guess I'll try a new M/C and see if that clears it up.
06-08-2011 09:39 PM
T-bucket23 You may have hurt the master while bleeding for the new cylinders. As joe stated in the previous post fluid may be leaking between the front and rear reservoirs. Try taking some fluid out of bot so they are down a quarter inch or so. Drive it and see if one side fills back up.
06-08-2011 02:39 PM
joe_padavano How old is the M/C? Does the fluid in the other reservoir go down? I had a problem once where one reservoir of my M/C would fill up and overflow like yours, but over time the other side lost fluid. There were no external leaks. I finally figured out that the internal seals in the M/C were worn and fluid was being pumped from one circuit to the other. A new M/C fixed the problem. I think you may have disturbed the old seals in the M/C when you bled the brakes.

It is also possible that the seals in the combo valve are bad, allowing a similar transfer of fluid, but my money is on the M/C. Those are the only two places in the brake system where fluid from one circuit can flow into the other circuit if there's a bad seal.
06-08-2011 01:48 PM
Fat 48 The cover fits tight. I think the key clue here is that there was no leak prior to replacing the wheel cylinders, so the leak is perhaps due to something I did while bleeding the system, or something I failed to do. Is it possible that replacing the wheel cylinders tripped something in the proportioning valve that's causing a pressure build up in the M/C to force fluid past the gasket whenever I depress the brake pedal? Or if the fluid level in the M/C dropped too low would failing to bench bleed the M/C cause this problem?
06-08-2011 01:42 PM
crownver Is the cover bail tight enough? Maybe a nick in the sealing surface of the master cyl.?
06-08-2011 12:48 PM
Fat 48 Thanks. I tried a new lid and gasket but it's still leaking.
06-08-2011 12:39 PM
adantessr You would have to have a bad gasket on the cover for it to leak . The rubber gasket has sort of a diaphram function to allow for expansion of the brake fluid. Make sure that it is installed correctly. If the gasket is good and installed correctly, theoretically, you could turn the master cylinder upside down and not leak any fluid.
06-08-2011 12:23 PM
Fat 48
Master cyinder losing fluid from cover

I have a disc/drum set-up, 7" booster with 82 Corvette master cylinder. I replaced both rear wheel cylinders and now have brake fluid leaking past the gasket between the lid and the body of the M/C when the car is driven. It was not leaking before I replaced the wheel cylinders. The system also has a prportioning valve which I suspect may somehow be the culprit. Any suggestions on what to check would be appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:26 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.