Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> I damaged a body line, and unable to fix.
User Name
Password
lost password?   |   register now

Thread: I damaged a body line, and unable to fix. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-25-2011 10:57 AM
deadbodyman Well ,use it for your filler you can guide coat the filler to make things easier,but the long block will tell you exactly where the metal problems are and where to knock them down
06-25-2011 10:39 AM
66SSImp454 This is great, thanks for keeping me grounded. One issue I was having is that this was mostly a high area, not so much of a low issue. This was right on the crease.So I used the porta power between a work bench and exterior part of the body to push the crease in a little with the chisel tip and I was able to hammer and dolly a lot of the high areas out. A straight edge and patience was used that this point (thanks Sam) and as all of you suggested I will move forward with the body filler. I do have a couple questions.


Tech69, when you say to "use tape to sand the top" what do you mean? I have heard of using tape to tape off a body line then apply filler over it. Also the bottom area (just under the body line crease) is not a flat surface, it acutally has a slight crown to it. So not sure if I can still keep it at 45 deg as the block. Any suggestion on how to handle that?

Deadbodyman, I don't understand when to use the long hard block.


Thanks agian
06-25-2011 08:29 AM
deadbodyman The guys are absolutly right,its time for filler..The problem with metal working is that it looks so ez when a pro does it and it sounds ez when they explain how to do it. but it takes years and years to even half as's master,Dont expect to do a fillerless repair you'll only frustrate yourself...You gave it your best shot and it looks pretty good. now move on thats what we do...knock down your high spots and start with the filler...use a long, hard block.
06-24-2011 10:36 PM
tech69 that's an easy fix. The top of the line is curved but the bottom will allow you to run a block off of it at a 45 degree angle. THAT is how you'll get your line back with filler. Let it define itself. Hopefully the top isn't too curved so you can angle it less than 45 degrees and run it off the bodyline, but if not use tape to sand the top. Then sand on the body line last.

check out this video at the 4 min mark. Watch the part where I blade in filler on a bodyline and how I sand it. Again, not the greatest example.

http://www.youtube.com/watch?v=LoqM3bFzdDk


this technique works REALLY WELL on bodylines and especially curved wheel well bodylines without worrying about what they'll look like in primer. It's works so good you don't have to use surface cleaner to check to see what it will look like in primer cause you KNOW it's gonna be good.
06-24-2011 02:41 PM
swvalcon Thats what they made bondo for.
06-24-2011 11:18 AM
OneMoreTime Can you put a straight edge on it to see just how much out of whack it is?? Takes a lot of patience to work that out by metal work..let us know..

Sam
06-24-2011 09:57 AM
66SSImp454
I damaged a body line, and unable to fix.

Hello,
I hope the pictures are not annoyingly large. I installed the quarter panel patches and I am not sure if it was caused from heat or how I damaged the metal but I am stuck and I am not sure if I can fix it. What happened is that there was a vertical crease that went through a body line. Using a hammer, dolly (best I could, see below) and shrinking disc I was able to work most of the crease out but that has left me with a really rough body line. The body line is a horizontal inward bend, and as it sits is more of a buldge.

To make it more difficult, there is no way a dolly will fit behind the area that needs to be worked on (dolly is too wide) but I did make a dolly with some flat steel and rod to help act as a dolly and since I have made it I am having better results but it still looks like junk. When I hammer it out (I have also used some masking tape on the hammer face) the metal is not smooth but body line looks better then to smooth it out I use a shrinking disc but I think that I am shrinking the metal too much because all that seems to do is raise the body line. Using air instead of water seems to be more controlling and I am using soap on the disc.

The pictures do not show the situation very well, but I hope it helps. Let me know if you would like some different angled pictures. Thank you in advance for any suggestions offered.

Damaged are is just above the wheel, and this occured on both sides of the car.







Thanks agian.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.