Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> power steering pump issue
User Name
Password
lost password?   |   register now

Thread: power steering pump issue Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-01-2011 09:35 PM
Bigolotava No problem... if you didn't mess with the pressure regulator, I wouldn't touch it, unless it's leaking and you have a new O-ring for it.

On your power steering pump there's a what looks like a large bolt on the rear of the reservoir that the high pressure hose screws into. This is actually a flow control valve. Check-out the link below for a great close-up picture that explains it very well: http://www.pozziracing.com/Media/PS%20valve.jpg

1 = Flow Control Valve (O-ring goes in groove to the left of the groove labeled "A")
2 = Pressure Regulator (easy to install backward if you've never done before)
3 = Spring

Anytime you remove the flow control valve, you should replace the O-Ring, as it gets hard with age and fails to seal, causing an annoying drip/leak that often is mis-diagnosed as a leaky high-pressure hose. You can get replacement O-rings at NAPA, your GM dealer, Autozone or Checker/O"Reilly.

Prior to installing a new O-ring it's best to wrap a piece of Masking or Duct tape over the threads (they're sharp!) to avoid tearing or cutting the new o-ring when you're installing it. Once installed, remove the tape and you're good to go!

Hope this helps,

Kevin
06-30-2011 03:12 PM
truckboy61 thank you for replying im still learning can you explain about pressure regulator for power steering and how to verify if its correct ? I only replaced pump and hoses ?
06-30-2011 03:07 PM
Bigolotava The port closest to the front of your Elky is the input and the rearmost is return. If it's correct and still spurts, the pressure regulator is probably installed backwards.

Good Luck!

Kevin
06-30-2011 12:18 PM
truckboy61
power steering pump issue

66 elky just replaced power steering pump and am getting fluid shooting up through cap ? tried bleeding and just took off lines to make sure nothing stuck that's creating back pressure ? When standing facing car and steering box which fitting is power and which is return maybe I got them mixed ?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.