Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> help with motor mounts
User Name
Password
lost password?   |   register now

Thread: help with motor mounts Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-25-2011 06:37 PM
Pupsvette76 i decided on a rack and pinion conversion its just overall a better choice in the end instead of spending the money on a different box to try and sqeeze it in just wanna eliminate it and all the clunky linkage and simplify and make room with a better steering system
10-19-2011 06:13 AM
TroyBoy I tried the block huggers one time. Won't work . The outlet points directly at your pitman arn and is too close to it . I already have the manual box on mine and it will give you a lil extra room if you don't already have one.
10-19-2011 01:57 AM
ericnova72 If you have a power steering box currently, a switch to a manual box will gain you quite a bit of room, it is smaller.
10-18-2011 07:56 PM
Pupsvette76 yeah i was thinking to maybe use one block hugger header i have an extra on it sucks though cuz the manifolds i have are real nice not just that they are shiny stainless but also i liked the idea how the connect together it was a good design in theory i guess
10-18-2011 07:51 PM
bigdog7373 Use one of the headers from the twin turbo motor and one regular header. Or have someone modify the ones you have. Its not that hard if you have the right tools. I would not raise the engine.
10-18-2011 06:40 PM
Pupsvette76 its just that thats one thing i dont have the expertise to start modifying so im trying to work with them... i had twin turbos on the car but decided to go with a single turbo and the header that i got for single turbo are the ones im having trouble with ... if i felt comfortable cutting them up and making the work i would but i have never done that before so im trying to look for alternatives... i think im ok in the heat dissappation area because i removed the inner fenderwells and only one turbo now
10-18-2011 01:55 PM
techinspector1 Unlike naturally-aspirated headers, turbo headers don't have to be tuned, so you can cut 'em up and/or modify 'em until you get 'em to work. From a performance standpoint, you could probably make the same power with cast iron log manifolds as you could with a set of fabricated headers, it's just that the headers would have more eyeball.


Be careful raising the motor/trans. Some of the heat of operation finds its way out of the car between the bellhousing and the transmission tunnel. You're gonna make more heat with a turbo and you don't want to be cutting off some of the escape route of the hot air from the radiator.
10-17-2011 10:04 PM
Pupsvette76 thats why im trying my hardest to use what ive got
10-17-2011 10:02 PM
Pupsvette76 well its set of turbo manifolds they are not easy to make
10-17-2011 08:16 PM
bigdog7373 Why not get different headers/manifolds. They dont work with the the car. Dont change the car to fit the manifolds. You're also raising center of gravity. Not a good thing if you want it to handle well in turns and such.
10-17-2011 01:35 PM
Pupsvette76 no i didnt do that yet... that s a good idea since i have to do it anyway in order to put the header in anyway
10-17-2011 08:06 AM
123pugsy Have you tried lifting the engine yet to the hgt you think would help?

If so, does the tranny hit the tunnel?

Might be good to pull the mount bolts and give her a lift to see what issues may arise.
10-17-2011 07:52 AM
Pupsvette76 yeah i see what u mean... the only thing is that im using a set of prebuilt turbo manifolds the driverside is almost like a regular header and it crosses under the pan to the other side and goes thru the passenger side manifold and out of the turbo... since the headers are the way they are i have to make everything fit around them ...what else can i do any ideas...on the driver side its hitting the box...and on the passenger side the tube for th wastegate is hitting the frame just a tiny bit and also the lower part of the pass side is like a millimeter away from the starter i think a mini starter will solve that problem though... the box is the big issue
10-17-2011 06:00 AM
TroyBoy If you are fabricating all this to begin with, why don't you just move things around to make them work with the car as-is I own a 70 Nova and I understand the steering box problem. It just seems to me that if you raise the mounts, you will also throw off the trans mount(will also have to be raised) then the drive shaft angles, then the pinion angles. See where I'm going with this?
10-17-2011 03:18 AM
123pugsy You can pick up small pieces of any steel at Metal Supermarket or a similar metal center.

You could also use 3 pcs of a solid round bar with a hole drilled thru the middle. Anything would be better than stacked washers.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.