Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Shaping convex body panels ....
User Name
Password
lost password?   |   register now

Thread: Shaping convex body panels .... Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-14-2011 10:46 PM
dsraven what I have done in the past is not go straight up and down on the panel. go at a crosshatch pattern with the durablock, that will take off the high spots and not allow you to make the same groove over and over. then when you think you have it, wipe it down with a wet rag full of wax and grease remover and that will show a shiny surface for a few secs. you will be able to stand back and see any ripples in the finish, just like it was freshly painted.
just an idea that worked for me.
dsraven
12-09-2011 06:15 PM
57chevy350 Cboy good on you !!!! nice hotrod ! dixiedart it's all about time take your time use your hands eyes and a guide coat !!!! good luck .
11-27-2011 05:03 PM
dixiedart Cboy -

That's exactly what I'm talking about. I'm using the same Dura block plus others, thanks for the tips. I'd consider the cardboard template trick but, the other side is in the same state !
11-27-2011 03:35 PM
cboy Don't know if it will help at all but here is how I approached the challenge of getting convex curves fairly straight on my sedan delivery.

Here are a few shot which show some of the tools and techniques I used. Much more detail in the link above.









And here are a couple shots showing how the curves turned out.



11-27-2011 02:28 PM
Sir Joab I think for most of us this is a matter of feel... However, you could also take pieces of cardboard and cut one edge to fit up against the body (say, along those red lines on your picture) using the "good" side of the roof. Then lay on the filler a little too thick and sand down until the cardboard guide sits properly in place... homebuilt aircraft builders sometimes use this method for shaping wingtips.
11-27-2011 07:39 AM
dixiedart
Shaping convex body panels ....

So I'm filling the factory roof seam after cleaning and sandblasting - factory used some lead and some filler - I used short strand glass and finishing up with polyester. I'm having a real time with shaping this "outside" or convex curve. I need to learn how as this will not be my last rodeo - how you guys work with "bubble" tops and fat fendered cars and get 'em perfect is magic. I can handle a straight , flat body no sweat (66-67 Fairlanes, Novas, Chevelles) but I need tips on shaping these types of areas as this is a first for me. A link to any videos known of would be great ! This is my own car, I'm just a weekend warrior.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.