Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Modern Electronic Engines> Chevy C6500 truck with 454 engine install distributor with cam sensor
User Name
Password
lost password?   |   register now

Thread: Chevy C6500 truck with 454 engine install distributor with cam sensor Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-23-2012 09:08 PM
jwhobbs
Chevy C6500 truck with 454.....

At what point on the rotor is considered the pointer that needs to be aligned with the #8 on the dizzy housing? My counterblancer does have degree marks.
01-22-2012 07:14 PM
LATECH No. Put the rotor at the little number 8 on the dizzy housing. Dont pay any attention to the firing order.Be sure when it is tightened down the rotor points at that little number 8. The 8 is to reference the dizzy as used in the 8 cylinder. Some of those dizzys had a 6 and an 8, and could be used in either a 6 or 8 cylinder, and were marked for reference accordingly.
01-22-2012 07:09 PM
jwhobbs
Chevy C6500 truck with 454 engine.......

Thanks I will try this. Does the number 8 on the rotor need to match number 8 on the body of the dizzy?
01-22-2012 05:51 PM
LATECH IIRC there are no timing marks on the balancer, just 3 or 4 little cuts in the front edge.
What you need to do is turn the engine by hand with a socket wrench on the crank bolt, untill you get tdc #1 compression stroke.
Being there is no timing marks you have to rely on your expertise to gauge TDC through the spark plug hole.Then if you can put on a timing tape, back it up to 14 degrees BTDC.
At that point you are ready for the dizzy.If you look real close at the dizzy, where the cap touches the edge at the place it mounts, there is a number 8.
You want to drop the dizzy in the hole and end up with the rotor aiming at that number.
Now the 14 degrees BTDC may be hard to get to, but one of the little cuts in the balancer should be at the bottom where you can see it.I think that is 14 degrees when it is straight up and down, IIRC. Been several months since I did the last dizzy gear change and set one up.
Now when you get done, If it throws a code p1345, then you need to re learn the cam/crank angle. If the data stream shows that you are 7-13 degrees BTDC on the cam sync pulse timing then it is timed correctly and all you need to do is perform the relearn according to the scanner instructions.
01-22-2012 05:16 PM
jwhobbs
Chevy C6500 truck with 454 engine install distributor with cam sensor

Yes.
The only thing this unit does is drive the oil pump and send signal to computer where cam is located.
01-22-2012 04:30 PM
LATECH Is that the plastic distributor, with the hold down that only allows the distributor to go in one posistion?
01-22-2012 02:06 PM
jwhobbs
Chevy C6500 truck with 454 engine install distributor with cam sensor

How to install distribuotr with cam sensor into 454 Chevy engine to be in time with crank sensor?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.