Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> How big of a NOS shot can pump gas take?
User Name
lost password?   |   register now

Thread: How big of a NOS shot can pump gas take? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-13-2012 05:29 AM
Originally Posted by whyholdback
Here's what I've found success with:
Which has been replaced ( and updated ) with this:
Sweet I will look into it.
02-12-2012 09:50 PM
ethn_bert I run the mallory hyfire 6a box(685) w/ rpm switches and timing retard features. I have these boxes in both of my novas.
02-12-2012 09:24 PM
whyholdback Here's what I've found success with:
Which has been replaced ( and updated ) with this:
02-12-2012 08:58 PM
Hotrod 80 Do you have a system now ? I also would only run a wet system . Are you looking at a plate or a Fogger style ? I have seen 250 sprayed on 93 with a fogger and a MSD box pulling correct timing and a properly flowed fuel system .

I had a 355 with forged flattops and a NOS cheater plate kit and sprayed 82 square jets on 92 with the timing pulled manually 2 degrees per 50 hp .
02-10-2012 04:35 PM
68NovaSS While the bottom end is important at higher power levels, it's the pistons that will suffer from detonation first, forged, cast, hypers, they all melt.
02-10-2012 10:02 AM
blight So with a full forged rotating assemble (balanced) on 93 octane and the 10.5:1 what would be pretty safe then?
Could I run a 200 shot? Could you tell me more about these controllers?

Are there better ones than others?

As for the cam what does it need to be a nos cam a wider lsa? is a 110 enough then?
02-10-2012 06:13 AM
ethn_bert NOS recommends premium fuel above a 50hp shot. Whyholdback offers some good advice. I also use a controller with much success. A wet system is much safer at higher levels. I would never use a dry shot system. I've sprayed 200hp with 94 octane, a wet system, and timing retard box for years with no issues. However, I run much lower compression and a camshaft for nitrous.
02-10-2012 03:32 AM
whyholdback With nitrous, octane becomes less important. Nitrous cools the charge enough to fight detonation. But it also accelerates the burn. This is why we pull timing as we add more nitrous. You don't want peak cylinder pressure before the piston gets to top dead center on the compression stroke.
For a typical stock 350 with cast pistons, a 125 shot is safe. I've done 200 with cheap hypereutectics and the Jacobs' Mastermind progressive controller, on 91-octane. I set it for 50% at 3000, ramping up linearly to 100% at 6000. Very safe, since it was also pulling out spark advance as it was adding nitrous and fuel. It has adjustment for that as well.
02-09-2012 10:03 PM
How big of a NOS shot can pump gas take?

On a sbc with aluminum heads, 10.5:1 compression, 700cfm carb, using nothing higher than 93 octane. How much (like a 100 shot 50 shot?)nos can one run without worry that every-time that button is pushed that a piston is going to crack? Please bare with me I know as much about nos as I do about having my manstrual-cycle sinking up with the other guys manstruals that I hang around.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:55 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.