Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Engine Stand Bluebrints
User Name
Password
lost password?   |   register now

Thread: Engine Stand Bluebrints Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-26-2012 04:38 PM
mikey44 53 ford guy .. I see you are from Canada. Princess auto sells pretty good ones thar fold up out of the way when not in use and they are pretty cheap ... $159 or $169 sometimes cheaper on sale. I've had one for 4 or 5 years and still works well
02-26-2012 03:09 PM
1966mustang
Engine Stand design

I found a website that allows you to download "The Racer's Guide To Fabricating Shop Equipment" yall should check it out

http://gucabier.blog.com/2011/11/19/...orgiann-smith/
01-04-2005 04:17 AM
atlantis At those prices you mention for the equipment it's obvious that material cost for a homebrew project will probably be higher.

Only is it impossible to find such equipment in Switzerland at those prices, here all you usually get is the professional equipment at professional prices. So you'd pay more for the crane alone than you paid for all your equipment. And finding used equipment is like looking for a needle in a haystack. The fact is that there are just not enough car enthusiasts who do everything themselves and need such equipment over here.

Regards
Martin
01-03-2005 08:02 PM
julmer This won't work for Europe but these are good items to buy from Harbor Freight. Watch the sales and you can get them cheap and ready to go, likely for less than you'd pay for the steel alone. I have an engine stand, an engine hoist, and a 20 ton H-frame press. They work great for me and I've got less than $400 invested in all 3. I like to save my effort for other things when I can find that type of equipment cheaply.
01-03-2005 04:22 PM
redsdad If you are a Sam's Club member or know someone who is, see if your local Sam's has or will get you a 122442. This is a Goodyear Racing engine hoist. It comes with an engine leveler, has low profile leg design (wheels are up in the legs so it will roll under low cars - if you ever used one with casters under the legs, you will understand), folds up, and is a very nice piece. I bought mine for $169.99 plus tax in Tulsa. From the Sam's web site, it may have gone up $7. Unless you are getting the steel for free, I don't think you can build one this cheap, even if it is not as nice. Go to the Sam's web site and search for 122442.
OOPS. I just noticed that most of you are in Europe. Don't think there are Sam's Clubs there. Oh well, those in the States reading this thread should check out the Sam's unit.
01-03-2005 03:50 PM
atlantis Here I found another link which could be of interest:

http://www.oldengine.org/members/randmingold/crane/
01-02-2005 06:58 AM
atlantis Could you possibly provide scans from this book?
01-01-2005 08:44 AM
Canadian Charlie I bought a book from The Eastwood Company 12 years ago called "The Racer's Guide To Fabricating Shop Equipment" I made an engine stand from it and I'm proud to say that after 10 years its still going strong
01-01-2005 07:37 AM
adtkart I would be a little concerned about using that lift with the floor jack. I am not an engineer, but we have several on this board that may agree. It appears that there is alot of stress on that little jack. They are designed to lift relatively straight up, and rated accordingly. Lifting something, of considerable weight, that far from the lifting point on the jack, would require considerable strength. Consider that, by the time that you lift the tubing and chain from that end and angle, you have used a large part of the capacity of the jack, what is going to lift the engine? Ever try picking up a piece of square tubing from the end and holding it straight out? That is what that engine lift is trying to do. Then also pucking up an engine. It would have to be a 30 ton jack for me to feel comfortable with it.

The engine stand that is at the German site looks like it will hold up most any engine it needs to. I built one many years ago, using 2 1/2" angle iron, that I welded together to make tubing. I don't have the braces on it, like he does. Mine has had a complete 390 Ford engine on it and didn't budge a bit. If I was going to do alot with long straight 6's I would probably add bracing.
12-29-2004 01:59 AM
atlantis I have done research on this before and know it's not easy to find info. My latest search yielded the following link:

http://www.jpegstore.com/vwsyncro_LD...e=1&strSearch=

I don't think it's a good idea to build a hoist this way, especially not for v8 engines, but you might be interested.

The attached pic shows a hoist which is obviously made using a bottle jack, but unfortunately I have no more info on it. But I think this is the way to go to build a budget hoist.

Plans for building an engine stand which is suitable for v8s can be found on a German site:

http://www.amiportal.de/modules.php?...article&sid=37

The problem is if you don't understand German it could be difficult to follow.

Regards
Martin
12-29-2004 01:03 AM
atlantis I'd be interested in those as well. Especially if anybody has ever built a shop hoist using a normal bottle jack and not a specialized hydraulic cylinder.
12-28-2004 11:45 PM
53fordguy
Engine Stand Bluebrints

Anyone Have a Good Set of blue Prints That I Can Build A Nice Stand From? Im also Thinking Of Building A Hoist If Anyone Has Blueprints On them Could You Please Send Me Them....

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.