Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Braking solution for 1983 Silverado. Help
User Name
Password
lost password?   |   register now

Thread: Braking solution for 1983 Silverado. Help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-24-2012 04:15 AM
dsgb610 I currently have 295/50/15 tires all around. The rear end is a drum axle with limited slip and 3.73 gears. (5-Lugs) Do you have a link for the stainless steel brake lines? For now I plan on going with the brake lines, ceramic pads and bigger rotars.
04-23-2012 05:21 PM
Dizturbed One 2WD? 4WD? What axles? Any rear end upgrades planned?

Get a set of Stainless Steel brake lines for your disc set up front, big difference in feel and actual force applied to the brakes. Best "bang for the buck" you can get for brake performance, in my opinion. The front brakes handle most of the braking force on almost all vehicles, this is especially true of pickup trucks.

If I were you, I'd plan on swapping to discs in the rear soon. The stainless steel lines won't be much change on the drum brakes out back and it's cheaper to put discs in the rear than to do anything else. The big brake aftermarket is insanely pricey. The cheapest brake conversion I've seen for these is $500 for one axle, and the brakes were not impressive looking.

If you're in a 5 lug truck, you could get an entire OEM disc rear-end and stainless steel lines for half of that. New rotors and pads for another $150. New calipers would still have you cheaper. Plus you can get one with limited slip and the gear ratio that you want if you're picky. Also the added benefit that you can go to any Autozone, O'Reilly, or Napa when it comes time to do your brakes again.

You can go through it at your leisure, when time and money will allow, and install it when you're done. Rear ends are cheap to buy and cheap to go through.

There might be swaps to a bigger rotor and caliper from another GM vehicle that would be feasible (like 'Vette brakes on Camaro's). But watch out, because when I looked into that for my Camaro, the extreme prices of having to buy bigger wheels (and new tires to fit the wheels) to fit over them still ruined it for me. I'll now be waiting until it's painted and the wheels are picked, then just stuff whatever I can fit behind them into it, probably some C5 Corvette brakes up front and the disc setup off a 93-02 Camaro out back.
04-23-2012 12:55 PM
dsgb610
Braking solution for 1983 Silverado. Help

Just occurred to me that my 1983 Silverado has almost twice as much torque and power as my DD 1998 Volvo with less efficient stopping power. Been a member since 2007 and ive always wanted to go fast, having achieved that goal I admit I never thought to look at the suspension and brake end of the spectrum. The Truck Currently has Leaf Springs and front Disc Brakes. What are somethings I can do (in order of cost) to improve handling and stopping power. I am willing to do anything and a full disc setup is years (maybe months) down the road. Thanks for help in advance

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.