|05-28-2012 10:53 AM|
|05-27-2012 09:17 PM|
Pros definitely need quality, dependable tools. No argument there. Just trying to fill the OP in on my own personal hobbyist experience. I respect all the advice the pros around here have to give, good stuff!
|05-27-2012 12:25 PM|
|deadbodyman||absolutely. Just be for warned ,I seen a lot of weird things in my years and useing those guns is a crap shoot You never know when they'll getcha buy they WILL getcha.like the time my painter was showing me how nice that 35 .00 gun was spraying and I had to admit it looked just as slick as anything I did with my nice guns and just as I was about to say so the fan knob fell of while he was laying down a beautiful last coat well that knob rolled all the way down the hood right through all that beautiful work, it made me sick.they just aren't built well and something off the wall will happen .He dont bragg much about it any more because I took the materials and extra labor to redo it out of his pay that week ..I explained how I made all these mistakes learning too and I paid dearly for them I dam sure aint paying for yours too especially when I warned him and he didnt listen....If something like that happens to you its not such a big deal ,redoing it will only get you better..for us it can put the whole week off kilter and customers get upset when they're cars arnt ready on time...go with a better gun You'll never reget it....|
|05-27-2012 10:51 AM|
deadbodyman, thanks for the tips. I am leaning toward the finex also (mainly because of the width of the spray pattern), though to tell the truth, after seeing andy's video I may try one of those 43430 replacements. I realize results depend a LOT on the person doing the painting.
I assume the reason the 1.4 tip is better than a 1.3 for clear is the higher solids content?
|05-27-2012 10:45 AM|
hey larry. thanks man. I used 35 psi with the trigger pulled, but its possible it would have sprayed just fine with a bit lower psi. I'm not exactly sure what people like to use with this particular gun. (66222)? Anybody?
With the super cheap HF gun I was using 45psi and getting lots of wasted overspray bouncing off the panels.
If your paint is not coming out as slick as you like, you might try laying the 2nd and 3rd coats on a little heavier. Everyone says to spray the panels like you want them to look...so I hammer it on pretty good. And of course, that increases your chances of getting runs too. Its a razors edge between runs and orange peel for a novice painter. Luck helps alot too.
Thank God for colorsanding and buffing!
Good Luck, whatever gun you wind up using.
|05-27-2012 10:37 AM|
I noticed that the pressure at the tip with the new gun that I used-the 47016-seemed more like a conventional gun. while marketed as an HVLP, it is not described as such in the instructional materials that came with the gun
|05-27-2012 09:12 AM|
That Finex sounds like pretty darn good gun with some nice features. I'm changing my mind and think I would buy that one if I needed one...But first I would go to the SPI forum and ask what they (the painters) thought of it....either way you look at it ,it seems like two choices Sharpe and Devilbis.I'm sure both spray great so I would say hold them both in your hand see which one feels most comfortable Hold the gun in all the posistions it'll be in when your painting (how you would be holding it when painting a roof ,Rockers and hood...Then which one is lighter and you really want the big cup..The Sata type cups with the snap on lids are pretty nice if the lid fits nice and tight But a screw on cap really sucks and is a pita...so you also want a big cup with a snap on lid...And A 1.4 tip That's a MUST have....
be sure to concider tip size when comparing guns both guns should be the same
My Sata with the 1.3 is great for spraying base but cant spray clear near as well as my Iwata does with a 1.4 but the Sata with the 1.4 sprays just as good.so if there not both 1.4 tips your comparing you wont be getting the best gun for YOU...A 1.4 tip is the best choice for a tip size that will spray everything well..
|05-27-2012 08:53 AM|
Short video. 1 hour after 3rd coat. As sprayed. $35 gun.
|05-27-2012 06:25 AM|
larry, you might try the "better" purple gun. Its around $40 and comes with regulator. They use a small amount of oil on the parts when put together so clean it really good first, but no silicone inside like the really cheap purple gun. The good one is #66222 I think.
Its more of a true HVLP as the cheaper one says HVLP but is really just a conventional gravity gun. I used a new one (66222) this morning to spray a hood and cowl. sprays pretty darn slick without a ton of overspray. 35psi with trigger pulled. I'll put a pic up in a little while.
Its definitely night and day over the really cheap version.
|05-27-2012 06:20 AM|
|Lizer||Camino has me interested in that Finex now should I ever need to get another midlevel gun. Sounds like a nice piece. The main reason I went with the Finishline is because it came with three different tip sizes.|
|05-27-2012 06:13 AM|
|fleetsidelarry||thanks for the replies, guys, I appreciate the information. I knew with a question like this there probably wouldn't be any consensus.|
|05-26-2012 08:53 PM|
|67Elcamino||Ive recently played around with the finishline and finex3000. I really like the finex. Bigger fan, better adjustment control, uses less air , better atomization, way easier to clean(less parts) , a lot lighter than the finishline. For some reason I just couldnt get used to the finishline and kept having issues with the spacer inside and making sure it layed flat when installing the tip.|
|05-26-2012 08:14 PM|
I shoot with the Finishline for all my primers. I've never shot bc/cc with it yet, nor was I planning on it. However I am probably going to be using it for that as well since I really shouldn't drop $300 on another gun when I've got a new house and 11 acres to pay for.
With that being said, for what I've used it for so far, it's been a very good gun for me (and I've sprayed with very nice Iwata's and Sata's, as well as $40 cheapos). However, I can't say if it's any better or worse than those other guns because I haven't used them. I'm also a hobbyist.
|05-26-2012 08:10 PM|
Finex. I've used others, but always come back to the ol reliable Finex.
|05-26-2012 08:00 PM|
|This thread has more than 15 replies. Click here to review the whole thread.|