Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Fender/Hood Alignment on 65 Impala
User Name
Password
lost password?   |   register now

Thread: Fender/Hood Alignment on 65 Impala Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-11-2012 06:13 PM
swvalcon I see the line your talking about. I always thought the fenders themselves where the same but maybe not. AS I said we use to interchange complete front clips from one to the other. This was back in the early 70's and we would do it if all the guy wanted to do was get it back on the road to drive it the rest of the way into the ground.
06-11-2012 03:52 PM
fosterdl
Body lines

OK, this is what I was refering to. I'm sure the fenders will fit either a 65 or a 66, but there is a definate body line change in 66. Hopefully I've done this so the pix come through
06-09-2012 10:46 AM
swvalcon The 65 and 66 should be the same. I know the grille and bumper are different. Back in the day when these where just old used cars we would put which ever one we could get from the junk yard on them. I know I put more than one 66 front clip on a 65 and the other way around.
06-09-2012 06:49 AM
fosterdl
New Info

OK, I have a friend who is a body man and he came over to inspect this. We removed the lower windshield molding and found that the left fender had been mounted too far back and too far inward, thus causing the problem. Also the two fender do measure up to be the same as far as the top line. However it wasn't all our fault as the mounting holes appear to be off. (too far forward pushing the fender back) So, off comes the fender to grind out those holes. I'll post as re-assembly resumes. Also I don't think 65/66 fenders are the same. If you look closely at a 66 you will notice that just above the fender wrap-around the body line takes a 90 degree bend down. The 65 does not have this feature. Otherwise they may be the same, I don't know for sure.
06-06-2012 10:45 AM
66SSImp454 I will certainly keep my eye open.
06-04-2012 07:25 PM
deadbodyman in your ventures to find parts if you see a 65 Impala wagon,please let me know. I'm trying to find any mojdings I can get.Right now I really need the drip rail moldings.
06-04-2012 12:04 PM
66SSImp454 Thanks for posting that up. This is perfect timing for me as well because I am just starting to put the front clip on.

a 65 with molding, it does look my theory is incorrect. Goes to show, not everything your read on the internet is true.
06-01-2012 08:10 PM
deadbodyman They should be very close, I set it up square and go from there ,with aftermarket fenders you never know what you'll end up with .I didnt get that measure but I can tomorrow,it could only be used as a starting point for setting yours up though
06-01-2012 08:02 PM
Stu D Baker Do you have the radiator support mounted "square" to the car, i.e., if you measured a "X" would both measurements be the same? Stu
06-01-2012 08:00 PM
deadbodyman Lengthwise,running the tape over he top of the bodyline,its hard to get an accurate measurementso I squared it off with a paint paddle and measured to that.From the fender edge to the stick is 61 1/4 "...I transferd the tape to the other fender fender and got exactly the same measure....These are aftermarket fenders....But they fit pretty well....I hope this helps if you have any other measurements or dont understand something just ask and I'll get some more ...The car will be here for one more week...
06-01-2012 07:45 PM
deadbodyman here ya go
Take some masking tape and eyeball aprox. the middle of the bottom of the fender,run the tape straight up from there right over the molding...Mark the top body line and the bottom ,then pull the tape and stick it on something to keep it straight then measure the marks ...Up and down is 30 "...I'm measuring the left fender (drivers side) then transferd the tape over over to the same spot on the right side,,,exactly the same 30"
06-01-2012 06:22 PM
deadbodyman AWE SHEET...I got the pics and showed how to measure them.then promptly forgot the camera at the shop....I'll go back and get it. I'll get back to ya in 30 min.....sorry
06-01-2012 04:07 PM
66SSImp454 To answer your last question, no all '65s were the same.

I know (as I am sure you do as well) that the '65 and '66 have a different front clip, where the sheet metal behind the firewall is the same, but different in front of the firewall. I am pretty sure this includes the fenders. By chance does one fender have molding holes and one not? If so, that is your problem for sure as the '66 had molding and the '65 did not. But not all 66s had moldings.

I don't understand what you are measuring. Are you saying that the actual fenders are different in length? If so, it sure sounds like you have one '65 and one '66 fender.

Let me know if you would like me to measure the fenders on my '66 and my father has a '65 but that one is a little harder to get to so it may take me a bit for measurements on that one. If so, please tell me where you want me to measure from and to. Pics may help me understand better your issue.
05-30-2012 09:18 PM
deadbodyman Well Tuesday it poured out and the guy wont drive it in the rain so it came in today.I worked my arse off on it and I was going to get those measurements for you at least 10 times then of coarse I plum forgot but I will get them tomorrow ,I promise.
Mike
05-25-2012 05:28 PM
fosterdl Great, Thanks !!
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.