Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> standard vs high volume oil pump in 555 bbc
User Name
Password
lost password?   |   register now

Thread: standard vs high volume oil pump in 555 bbc Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-23-2012 10:23 PM
67-4-fun HV pumps on averge can rob you of almost 10hp, if there is no need for a HV pump as mentioned usees for one, almost always a standard pump is the best choice..
06-23-2012 05:56 AM
joelster SBC's and BBC's have excellent oiling systems. A standard pump with a GOOD filter, such as a NAPA Gold, and quality synthetic oil, should get you all of the oil pressure you need. That old saying of 10lbs of pressure for every 1000rpm holds true. Anything over that and you are sucking extra hp to drive the pump. I had an old sbc with a high volume pump and on a cold start it would shoot up to well over what the gauge would read, lol. Gauge went to 80 iirc. At a hot idle at 850rpm it would have 40lbs. I thought it was awesome, lol. Little did I know I was losing power.
06-22-2012 05:54 PM
lmsport You can modify a BBC pump to dump the pressure relief back to the pan rather than cavitate it in the pump body. Then the load on everything is the same until the oil system needs the extra volume.
06-22-2012 05:31 PM
BOBCRMAN@aol.com It depends on how the engine was set up on build. Loose bearing clearance and other maxed out specs. will require HV pump.

I try to avoid them. If not done properly. They can cause cam wear problems on flat tappet engines. Both at the front thrust surface and the pump drive.
06-22-2012 05:29 PM
68NovaSS If you have wide bearing clearances a HV would help maintain pressure, otherwise I would go with a standard pump, JMO. I've heard pros and cons about a HV sucking sumps pretty bad, consider a deep pan.
06-22-2012 05:22 PM
dav770431
standard vs high volume oil pump in 555 bbc

I am wondering if I should run a std or high volume pump in my full roller dart 555 bbc. Its a street/strip motor. Ive heard std would be fine but high volume is a better choice.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:32 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.