Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Modern Electronic Engines> Question on 1996 Lumina
User Name
Password
lost password?   |   register now

Thread: Question on 1996 Lumina Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-10-2012 03:49 PM
price
lumina

Pull the fuel injection out and install 6 motorcycle carbs. This will take time but it will allow some breathing room while you figure out how Gm didn,t stay bankrupt.
07-10-2012 06:47 AM
T-bucket23 If it is a 2 crank sensor engine, it will run without the front one plugged in. Check to be sure you dont have 2.
Edit:
According to my documentation it has 2 crank sensors. Look at the 2 wire harness that goes straight down from the module to the back of the engine. I bet you will find damaged wires.
07-09-2012 10:30 PM
rx191 after it dies do you have spark?

That engine does use 2 crank sensors a 24x in the block reads off the crank, and a 3x that reads off the trigger on the balance. the computer uses this sensor at engine speeds above about 1800-2000rpm. I have seen the crank sensor at the front fail many times and never leave a code.

Also does it die like you shut off the key or does it die like you dumped the clutch in a stick shift car?
07-09-2012 09:50 PM
DoubleVision I was going to next start on cleaning the grounds and checking them all. This is the 3100 V6 and it has the crankshaft position sensor right behind the balancer. I am going to clean it up real good while I'm in there. I had the same idea that it maybe losing it's ground since it dies when rolling but not sitting and idling. I really appreciate all the good tips guys. I want to do the best I can to get this old lady's car back going so she can get around again.
I'll make sure to give the wires a tug to see if that shuts it down also, if so I'll know I have some wires to trace down. I also had read the oil on the sensor can cause it to read incorrectly. What puzzles me about the crank position sensor is why doesn't it throw a code? As said I had a car before this do the same thing and it never threw a code, it would just go dead.
Thanks again for the help guys.
07-09-2012 07:40 PM
T-bucket23
Quote:
Originally Posted by LATECH View Post
Hey thats right. They did use 2 crank sensors on the one design. Funny thing, the Mc parts stores stock the one that is easy to change, its not the one that fails either.LOL Its allways the one behind the balancer that fails. I guess they sell the easy one for the DIY guys. Then they bring it to the shop for you and me.
It is the "I replaced everything and it still wont start" customer. Got to love them and the ones who take what the kid behind the counter at Autozone says as gospel. Its what keeps it interesting.
The funny thing is they always think they are saving money by doing it themselves and they buy $300 worth of parts when they had a cracked vacuum line or broken wire.

I would like to have a nickel for every EGR valve that was changed that was not bad, or gas caps.
07-09-2012 07:12 PM
LATECH
Quote:
Originally Posted by T-bucket23 View Post
LA you just jogged something in my memory. I had one with the sensor on the back of the block near the fire wall and the clip that held the wire died with age. The wire was loose and it was shorting out on the exhaust manifold. Found a bare melted wire after tracing the harness. It was the wire that went right from the coil pack down to the crank sensor. It was a little later setup that actually used the 2 crank sensors but it is worth looking at
Hey thats right. They did use 2 crank sensors on the one design. Funny thing, the Mc parts stores stock the one that is easy to change, its not the one that fails either.LOL Its allways the one behind the balancer that fails. I guess they sell the easy one for the DIY guys. Then they bring it to the shop for you and me.
07-09-2012 07:06 PM
T-bucket23 LA you just jogged something in my memory. I had one with the sensor on the back of the block near the fire wall and the clip that held the wire died with age. The wire was loose and it was shorting out on the exhaust manifold. Found a bare melted wire after tracing the harness. It was the wire that went right from the coil pack down to the crank sensor. It was a little later setup that actually used the 2 crank sensors but it is worth looking at
07-09-2012 06:53 PM
LATECH Doublevision... which engine do you have? and which type of sensor does it have? I was thinking it has the Hall effect sensor behind the balancer.
The permanent magnet sensor was an earlier style , that pushed in through the side of the block. Not sure at what production date they changed.
I have had both style crankshaft sensors cause a diveability problem like yours.
An ohmeter may or may not give a good indication of a defective Permanent magnet sensor , if it ohms out , it could still be bad, if it has a couple windings shorted to gether, amplitude of the sine wave( PM Generator) may be lower than threshhold voltage required and the signal generated can have a momentary "flat spot" or "glitch" that fails to signal or trigger the signal processor in the ICM /ECM
Ohming a hall effect type sensor is not recommended as usually wont give a good enough indication of health of the sensor.
A hall effect is designed to generate a square wave signal that can only be checked with an oscilliscope.
07-09-2012 06:31 PM
S10 Racer You can test the crank sensor using an ohm meter. It should read somewhere around 500 - 900 ohm. If it checks out ok, I would be looking at the ICM
07-09-2012 06:08 PM
T-bucket23 I would also take a hard look at the power and ground circuits. Could be when you put it in gear and the engine shifts when you step on the gas it is pulling a wire in the harness. If it was heat related I would think it would also die if you let it idle. I cant imagine the temperature would change in a 30' drive.
You can locate the harness that has the wires for the crank and cam sensors and try moving it around to see if you can make it die.
When it wont start check for power and ground at the connectors for the sensors.
Not sure if Chevy had the same setup but on the Pontiac's and Buick's there is a ground junction in the drivers side door sil that gets all green. You could get to it by pulling the carpet back. I saw several of these on the Pontiac's and Buick's. The tip off was that usually the power windows or heater or something else didn't work or the windows would be real slow.
It was a connector with a metal blade that connected a bunch of grounds together.
07-09-2012 05:20 PM
LATECH Seems the power and ground circuits are tied together in paralell on the cam and crank sensor.
It sounds like a crank sensor to me also. I think the fault detection strategy on those old 3.4 is kinda faulty itself.
Your correct in assuming the cam sensor failing would not cause a no start no run situation also.That would be a crank sensor.
Put in the crank sensor.
07-09-2012 04:12 PM
DoubleVision It's fuel injected and I've checked the fuel pump. After it shuts off it's still getting good fuel pressure and the pump is coming on as it should.
07-09-2012 02:11 PM
copo nova Sounds like fuel pump sometimes will idle then as soon as you take off you use fuel in carb it will stop and now its hot so wont restart to idle tell it cools off.
07-09-2012 04:37 AM
DoubleVision
Question on 1996 Lumina

As stated working on a 96 Lumina. After getting past the Vats system on it and getting the car started it has a issue. I can start it and leave it at idle for 10 minutes, all's okay. Get in, put it in gear, go 30 yards it goes dead and won't fire back up for several hours. Only code I get is 341, camshaft position sensor. However I know it'll run without it so it made me think of the next culpruit, the crankshaft position sensor. Years ago on another vehicle that was similiar to this one I ran into the same problem, I replaced the crank position sensor and the problem was solved. It too never gave a crank sensor code. The one on it is coated with grease and oil, but I don't think that effects it much on how it works. I was reading the bigger possibility is the PCM has gone bum. I want to get other opinions on this before I bother changing the crank position sensor, as this car belongs to a old lady on a really strict budget. Any help is appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.