Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Automatic to Manual
User Name
lost password?   |   register now

Thread: Automatic to Manual Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-14-2012 08:10 PM
Grease_Fever I've done this twice.

Here's my current build, obviously your ability to fork out green is a factor.

I am running a Saginaw 4 speed (should be less than $500) behind a Chevy 305. Plenty of stout for the power I have.

You'll need a set of pedals which can be purchase aftermarket. Might need some modifications, but doable with a little fabrication skills

I recommend running a hydraulic TOB to make things easy and in my opinion, cheaper. Bought mine through Speedway and it works great. The first time I did this I set up a slave cylinder and the geometry was a pain. The hydraulic TOB was a breeze and I am running a stock master from Advance Auto parts, cheap too!

Don't buy a model specific bellhousing. Buy a new steel that will fit several applications in case you change your mind. Price will be comparable in any case.

You will probably need to modify your drive shaft and move your tranny crossmember.

Estimate $1000 for this route. I'd love to run a 5 or 6 speed myself, but that route will multiply your costs. I'm a little light right now to be specific. I hope this helps!
09-14-2012 07:27 PM
Lovemius I'd like to do a 5 speed, but a 4 will be the best option based off of the info you provided. You've been a great help, thanks.
07-23-2012 08:37 AM
AutoGear lots of info there.

Do you want a 4 speed 5speed or 6speed?

Cheapest would be a 4speed. You'll need the proper trans to fit your rear axle ratio (or vice versa). You'll also need the pedals, a clutch kit, flywheel, perhaps a crossmember, Zbar, trans itself, bellhousing, shifter, shifter linkage. Some other things to check that may need to be addressed (depending on whats been done to your car) Trans tunnel, driveshaft, console, seats.

Its not hard to do if you have a factory service manual

If you get into 5 and 6 speeds (which you absolutely don't NEED), the cost goes up and it'll be more work.

My recommendation for a budget install? Assuming a basic smallblock; an M20 with a set of 3.23s to 3.55s.
If you have 3.08s in the back; a 2.88 1st T10 or an M22Z (2.98). These get the mileage everyone wants, with lots of strength and you can use mostly factory parts for the install.
07-22-2012 06:06 PM
Automatic to Manual

Can anyone give me any advice on switching out an automatic transmission to a manual on my 1970 Chevelle Malibu? Costs?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 09:32 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.