Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> GM drum to disc swap
User Name
Password
lost password?   |   register now

Thread: GM drum to disc swap Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-30-2012 08:40 AM
bfhduh I am building a v8 s10 and been having issues stopping my tires at a stand still and i switched from stock drums to a 2004 stock blazer 3.73 dis1c and it solved about 70% of my problem. if that helps. didnt have to change anything bolted right up
06-07-2006 05:21 PM
Triaged I don't know if it is in the rules but a residual pressure valve should help part of your problem. The 50's MC would just make things worse. If the peddle effort isn't too high you might try a larger (power brake) MC...but your rear calipers will still be too big.
06-07-2006 03:44 PM
dundirtcheap If I obtained some calipers from the front of a 79 Camaro or 'bird, and used a single cell master cylinder (50's style), would I solve my problem? Trying to solve the problem before sat. nite.........gotta big race comin up........
06-07-2006 01:16 AM
Triaged What master are you using?

Starting in about 83 GM started to change the angles cut in the calipers for the square cut o-ring. This allowed the pistons to retract more from the rotor yielding more MPG because of less drag. However to do this they needed to use a step bore master cylinder. They had a large (40mm mostly) piston that would move lots of fluid and would transition to the smaller bore (1.125" in the case of the caprice) to keep peddle effort down. As you found out mixing the 2 up doesn't work too well. I also bet that you have way too much braking in the rear. Best bet would be new MC with a larger bore and smaller calipers in the rear (like metric calipers)
06-06-2006 11:44 PM
TooMany2count get a proportionary valve for 4 wheel disc brakes it should matter if they were power or not because the valve cant tell if u have power brakes or not. but then i would most likely run a power booster also if it was me.......joe
06-06-2006 07:56 PM
dundirtcheap
GM drum to disc swap

Swapped from drum to disc on the rear of my race car. Limited to stock parts, and used the calipers from the front of a Caprice wagon '85 model. Used manual master cylinder, with no proportionary valve. Problem: no pedal without pumping several times. Minimal pedal with numerous pumps. Not enough to stop car. Need stock combination to allow me to utilize the rotors I have. They are after-market .81 thick, purchased from Speedway Motors and are the only part I can use that is after-market. ANY and ALL assistance appreciated.........thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.