Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> caster camber & toe
User Name
Password
lost password?   |   register now

Thread: caster camber & toe Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-07-2012 06:24 PM
1937 PlyCoupe
Thanks!...

Thanks guys, it's nice to have a guru or 2 in your pocket.
The info you all related will be dialed in tomorrow.
If nothing else it will give me a base line to start and adjust from. Sorry bout the caps, this ole laptop is stuck on caps lock.
I'll test drive after the adjustments and let you all know.
Thanks again!
In the words of arnold..."i'll be bock"
ric
08-04-2012 10:40 PM
timothale
Lower A arms

The lower A arms should be parallel to the ground front to back and side to side. since this was a suspension swap the angles might not be right, also mustang II take less pump pressure than GM std pumps you can buy a shim kit for the pump to drop the pressure.
08-04-2012 07:47 PM
LATECH Yes, if you have a dummy weight to put in the car as the algnment is being done , that could help the outcome.
1/8 inch is standard on a lot of vehicles. Many newer vehicles, maybe not. More like .100 of an inch.
As the car goes down the road , suspension loads, and toe in changes slightly.The tire will tend to fold back, or apart in the front, which is why a little toe in is generally required, or desired. 1/8 of an inch is only 1/16 difference from front to back through the center verticle axis of the wheel/tire. almost negligible.Unless you factor a little for suspension "loading". That tends to zero the small amount of toe.
08-04-2012 07:17 PM
Ripper 410 I agree with most of what latech said except the toe I'd find a reputable alignment shop and have them set everything while i was sitting in it and the toe I would have set to zero that way when you are driving it it is tuned to your weight.
08-04-2012 06:57 PM
LATECH The OE specs wont help.
You should have 5-7 degrees caster, no camber (zero) or a little + camber...like less then 1 degree, and 1/8 inch of toe in.
08-04-2012 04:15 PM
1937 PlyCoupe
caster camber toe

No, the car is streetrod, built 383, 430 HP, front tires are wider and shorter than stock.
Mustang II front front end, rear tires stock height but much wider.
IFS
Any advice anyone can share would be great!
08-04-2012 02:47 PM
timothale
any changes ?

Is the Car stock ? you should be able to find original specs on a mopar resto forum. Is it the tubular axle or an IFS system.? I have had problems with tires wider than stock and a lot of offset in the rims. stock wheels and tires were OK, If you have raked the car, little tires in front, big rears it will change the actual effective castor angle.
08-04-2012 09:36 AM
S10xGN Can't help you on settings, but negative castor and/or toe-out will cause the problems you describe.

Russ
08-04-2012 08:22 AM
1937 PlyCoupe
caster camber & toe

HELP!, I can not find any info anywhere about what the caster, camber and toe in degrees should be for my 1937 Plymouth business coupe. The car wanders continually down the road. I always have to correct. Steering is tight but the wandering is driving me crazy!
Does anyone know the answer? If not, where can I go to get the answer.
There should be a minimum, maximum and a preferred for each function.
Please help!
Thanks!
ric

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:24 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.