Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> how to add stripes with bc/cc system
User Name
Password
lost password?   |   register now

Thread: how to add stripes with bc/cc system Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-23-2012 05:22 PM
astroracer Every layer of paint you lay over the tape will add to the thickness AFTER you remove the tape. Also, the paint will "gather" at the tape and create a higher edge then in the middle of the stripe.
I would use single stage and shoot only enough paint to get coverage. After it cures you can sand the edges and polish to reduce the edge thickness.
Mark
08-23-2012 04:28 PM
Vincentnova can i clear just the stripes and then remove tapes ?
08-23-2012 03:26 PM
1pickup
stripes

scuff the entire panel, tape & paint stripes, clear, done
08-23-2012 03:02 PM
Vincentnova i would like to use metallic paint
you think single stage its a good way to go ?
08-21-2012 04:35 PM
Lizer I had seen a good idea Brian mentioned, which was just to spray single stage for the stripes.
08-21-2012 04:13 PM
Vincentnova im not doing an entire paint job
the car is paint already
and the fact than you can feel the stripes , i like its like original ( its for a 72 CUTLASS)
08-21-2012 03:39 PM
302 Z28 The way I would do it is lay down your base coats first and within the window for applying clear (usually within 24 hours) tape off the stipes and apply base stripe color. Allow base stripe color to flash properly then apply a lite coat of clear overall. Follow with sucessive coats of clear.

If you apply the stripes after applying clear depending on the color you may wind up with a look like the strips are raised off the base.

Vince
08-21-2012 03:13 PM
Vincentnova
how to add stripes with bc/cc system

hello
im planning to add stripes on my car , using bc/cc
i would like to get some advise
i know it will be better to spray the base coat , take of the tape and clear the whool panel

but here i would like to know , if i just clear just over the stripes ( and after take of the tape )? m I going to get a sharp line ? a fragil line?

thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.