Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> need help with distributor
User Name
Password
lost password?   |   register now

Thread: need help with distributor Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-04-2012 06:34 PM
Live Action!
Live Action!

Thats carzy I seen it on ebay today but didn't know about the plate! thanks
09-04-2012 02:41 PM
Custom10 If you are in the market for an upgrade check this out

White Performance Detail Description

You just cant beat the value, they are easy to set up as well. Make sure you have firewall clearance. Lifetime warranty, 50 bucks, it is a no brainer.

Use it with this limiter plate, limit vacuum adv to 12-14 advance. The unit will add approx 20 deg vacuum advance out of the box, too much

Crane Cams 99619-1 - Crane Vacuum Timing Limiter Plates - Overview - SummitRacing.com

Try it at about 16-20 deg BTDC as the initial and 32-36 total. Use a simple 6/32 screw/nut with some lock tight to limit the mech advance on the HEI rotor plate, the hole is already drilled. The unit will have about 24 deg mechanical advance out of the box, too much.

Give it constant 12V from 15A fused 12 gage feed with toggle switch on dash or elsewhere within reach from driving position.

Have fun
09-04-2012 09:53 AM
Live Action!
Distributor

I'm sorry for the type'o it was 12 btdc.
09-03-2012 05:47 PM
cdminter59
Quote:
Originally Posted by Live Action! View Post
I have a 383 stroker with a mc1988 cam in my 73 impala, all parts have been up graded except my stock distributor; which was new thats why I used it also has points and dwell at 30. I have about 375 horse and 400 ftp torque. Was built for bottem end to mid range. I seem to get good mid and top but dont think the bottem end isn't were it should be.

1. Do I need to up grade to a Hei or Msd distributor and how many volts?

2.I have it set at base time 12 degrees Atdc.

3. Problem still running alittle rich, I have a 600cfm edelbrock turned out 1 3/4 factory set, also turned it back 1/2 to see if it helped.

4. In park I have Ideal speed at 750, Please help try to fine tune it! Thanks
I am with Delawarebill I hope #2 is a misprint. If not try setting it to 12* BTDC and use a vacuum gauge hooked to a vacuum port on the intake manifold. Advance distributor for the highest vacuum reading then move it back 2-4 in./hg. If engine pings decrease until pinging stops. Also you can adjust idle screws on your carburetor to the highest readings.
09-03-2012 05:41 PM
67Mustang Al.
Quote:
Originally Posted by T-bucket23 View Post
This is true of any ignition that uses a coil. As revs go up you have less time to build the field charge in the coil. The biggest issue with points is they become unstable at higher rpm and can bounce or float. The electronic distributors either use optical or hall effect sensors and they are just as stable at 8K rpm as the are at 800 rpm. Nothing mechanical to bounce around.
A good HEI is more than most street engines will require.
Years back i found a CDI diy kit with an output of 80,000volts that ran in conjunction with points ignition. I put twin kits on a Z900 Kawasaki which i drag raced. Problem was there was voltage going to the plugs sometimes but mostly it was jumping out at the frame and handlebars.
Electrifrying ride.
Al.
09-03-2012 07:51 AM
T-bucket23
Quote:
Originally Posted by 67Mustang Al. View Post
The thing with points ignition when there are 8 plugs to fire, the coil has to build up charge between each cap contact so the time is limited and when you build up revs there is less time for the coil to build up charge, so the voltage to each plug will decrease. The points cam follower whether its plastic or fibre wears and the points gap will become smaller as well after time.
I use an MSD ignition with blaster 2 Coil on my 347 stroker and it starts as fast as the key is thrown, has no issues at all and stays in tune. Street use only.

Al.
This is true of any ignition that uses a coil. As revs go up you have less time to build the field charge in the coil. The biggest issue with points is they become unstable at higher rpm and can bounce or float. The electronic distributors either use optical or hall effect sensors and they are just as stable at 8K rpm as the are at 800 rpm. Nothing mechanical to bounce around.
A good HEI is more than most street engines will require.
09-03-2012 07:32 AM
delawarebill
your #2 point

u say "Atdc" of 12... don't u mean BeforeTDC ????
09-03-2012 05:40 AM
67Mustang Al. The thing with points ignition when there are 8 plugs to fire, the coil has to build up charge between each cap contact so the time is limited and when you build up revs there is less time for the coil to build up charge, so the voltage to each plug will decrease. The points cam follower whether its plastic or fibre wears and the points gap will become smaller as well after time.
I use an MSD ignition with blaster 2 Coil on my 347 stroker and it starts as fast as the key is thrown, has no issues at all and stays in tune. Street use only.
It s all about dollars and performance IMO.
While working on a 6cyl, stroked BMW which we race,we tossed the electronic distributor and single coil away and installed a GM triple coil pack and crank sensor and reconfigured the computer to suit. Brilliant result for that car which is limited to 7400 RPM. It burns lots of E85 so you need a good spark for the extra volume of fuel going through.
Al.
09-03-2012 01:50 AM
Live Action!
need help with distributor

I have a 383 stroker with a mc1988 cam in my 73 impala, all parts have been up graded except my stock distributor; which was new thats why I used it also has points and dwell at 30. I have about 375 horse and 400 ftp torque. Was built for bottem end to mid range. I seem to get good mid and top but dont think the bottem end isn't were it should be.

1. Do I need to up grade to a Hei or Msd distributor and how many volts?

2.I have it set at base time 12 degrees Atdc.

3. Problem still running alittle rich, I have a 600cfm edelbrock turned out 1 3/4 factory set, also turned it back 1/2 to see if it helped.

4. In park I have Ideal speed at 750, Please help try to fine tune it! Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.