Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Building a 489 stroker
User Name
Password
lost password?   |   register now

Thread: Building a 489 stroker Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-15-2012 07:01 AM
cdminter59
Building a 489 stroker

When building a stroker motor it is usually best to purchase a rotating assembly. One first things to do is checkout your heads,(post your casting numbers)to know your combustion chamber size. Knowing the chamber size you can purchase your pistons for the compression ratio you want. Make sure the valves are at least 2.19 intake and 1.88 exhaust. You will not use your old pistons because the compression height is different on a stroker motor. Purchasing a rotating assembly is cost effective too. Here is an assembly from Summit Racing. Eagle Specialty Products B18021030 - Eagle Street and Strip Rotating Assemblies - Overview - SummitRacing.com. You will need to find a machine shop to do your block and head work. If you need help choosing a camshaft or any problems that come up you can discuss it with your machinist. It's a good idea to know if this motor is going to be a daily driver or a street/strip motor or strictly race. Know what kind of vehicle it is to be used in.
09-15-2012 06:53 AM
454C10 I recommend that you buy a complete kit (crank, rods, pistons, rings, bearings).

But first, you need to know what size heads you have and what compression ratio you need.
09-15-2012 04:10 AM
BOBCRMAN@aol.com Most stroker cranks require 6.385 rods. External balance is ok for a street/strip type motor. Otherwise it gets real $pendy quick, at balance time. As for valve clearance. Not knowing any specs on your motor.. Check on assembly.
09-15-2012 01:36 AM
vinniekq2 Internal balanced cranks are usually preferred.If the power is reasonable then let your budget decide what route to take.Piston to valve should always be checked when assembling an engine.The HD 7/16 GM rods are pretty good.If you need better than stock, then check with carillo or crower or any other good manufacturer for rods.
09-14-2012 08:28 PM
489chevelle I was also wondering should i get a internal balanced or external balanced crank
09-14-2012 08:27 PM
489chevelle
Building a 489 stroker

Im wanting to build a 489 big block shevy and had a few questions. I have a stock 454 that is already bored .030. i was wondering what rod length i would need and would i have good valve clearance with the stock flat top pistons with the small valve releifs? Any info would be appretiated thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.