Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Ford inch assemble procedure
User Name
Password
lost password?   |   register now

Thread: Ford inch assemble procedure Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-21-2012 11:29 AM
prostreet6t9 If you google it... There's a ton of pages.
09-21-2012 10:39 AM
V8Square
Rear end assembly

Quote:
Originally Posted by big gear head View Post
If you are using stock Ford retainer plates then the retainers must go on the axles before the bearings are pressed on. The axles and bearings will fit through the hole in the center of the brake backing plates. The backing plates will be sandwitched between the retainers and the housing ends. The bearings will stick out of the housing ends the same amount as the thickness of the backing plates so that the bearings will be flush with the backing plates when installed. The retainers will hold the bearings and axles in the housing with 4 T bolts and nuts. If you have the standard sealed ball bearings then you will need to install axle seals in the housing ends befpore you put the axles in. If you have the tapered roller bearings then the seals will be on the outer side of the bearings. DO NOT use axle seals in the housing ends if you have the tapered roller bearings.
Thanks for all the info. Now, if I just had an exploded wiew of the rear end...
09-21-2012 10:06 AM
big gear head If you are using stock Ford retainer plates then the retainers must go on the axles before the bearings are pressed on. The axles and bearings will fit through the hole in the center of the brake backing plates. The backing plates will be sandwitched between the retainers and the housing ends. The bearings will stick out of the housing ends the same amount as the thickness of the backing plates so that the bearings will be flush with the backing plates when installed. The retainers will hold the bearings and axles in the housing with 4 T bolts and nuts. If you have the standard sealed ball bearings then you will need to install axle seals in the housing ends befpore you put the axles in. If you have the tapered roller bearings then the seals will be on the outer side of the bearings. DO NOT use axle seals in the housing ends if you have the tapered roller bearings.
09-21-2012 06:56 AM
V8Square
Reassembly

Quote:
Originally Posted by OneMoreTime View Post
what is done is to install the 3rd member into the housing and then the axles go in with the backing plates..bearings are pressed on the axles..4bolts hold everything in place..then all tha tis left is to install the brakes and drums and good to go..

Sam
Thanks. So, after I install the third member, I install the axles, with bearings already pressed on. When installing the axles, will the retainer plate, once bolted up to housing, pull the axle/bearing in and seat properly? Also, do you know where I could get an exploded view of the rear end? Tom
09-21-2012 12:11 AM
OneMoreTime what is done is to install the 3rd member into the housing and then the axles go in with the backing plates..bearings are pressed on the axles..4bolts hold everything in place..then all tha tis left is to install the brakes and drums and good to go..

Sam
09-20-2012 07:16 PM
V8Square
Rear end assembly

Quote:
Originally Posted by OneMoreTime View Post
https://www.google.com/search?q=rebu...ient=firefox-a

Here are some links to that info..I send mine out as I have a resource that is reasonable and good..Takes a few special tools but is doable at home if you desire..

Sam
Thanks for the link. I already have my third member together. What I need to know is the sequence to reassemble the rear end. How are the axle bearing installed, etc? Tom
09-20-2012 03:50 PM
OneMoreTime https://www.google.com/search?q=rebu...ient=firefox-a

Here are some links to that info..I send mine out as I have a resource that is reasonable and good..Takes a few special tools but is doable at home if you desire..

Sam
09-20-2012 03:39 PM
V8Square
Ford inch assemble procedure

I knows this may sound stupid, but can anyone tell me the step by step process to assemble my 9" Ford rear end? I am new to all of this and need all th help I can get.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.