|10-03-2012 09:15 PM|
210 is popular with the OEMs because it really raises the efficiency of the engine and EFI does a lot to get them around the issues of the fuel losing octane rating as the engine gets hotter because they are injecting cold fuel onto the hot valve were it sits for a microsecond before going in to there isn't time for the chemical degradation to happen to the fuel as with a carburetor or throttle body injection before it gets to the valve. But 210 is also very edgy as far as the complete cooling system goes, one small thing goes wrong in the cooling system and the engine can be par-boiled before you can shut it off.
So running at 180-190 is a safer bet it gives a little space for cooling problems to be caught before disaster occurs and it gets the oil up into that magic range of 190-210 where it cooks the water and fuel contamination out of it.
Smokey thought that racing engine ought to be running at about 400 degrees but he couldn’t get there with the materials engines are made of. Way back in the late 1930’s with the war on the horizon the military was looking for a way to get more power from aircraft engines without having to make them bigger. So as part of the Hyper-engine program many attempts were made to get coolant temps up to around 300 degrees. But again the materials (even those used then were far superior to anything used by even today’s auto engines) just wouldn’t support those temps. Eythlene Glycol coolant was one part of that program which did filter to the automobile in the 1950’s as was detergent oil and the hydraulic lifter. All these things were products needed to operate at those extreme temperatures that found homes in everyday life. Today with ultra modern precision machining, the OEMs accepting the cost of better materials the much improved lube oils both mineral and synthetic, the lube oil is getting mighty thin and this requires temperature stabilization of the engine. These new ones heat and cool the oil and mix cold radiator coolant with hot return coolant in a proportion that keeps the engine hot (210 or so) and eliminates the temp gradients from cylinder to cylinder, chamber to chamber because the inrushing coolant is the same temp as the outgoing so that one part (like cylinder walls 1 and 2 on the SBC) of the engine where the coolant is coming in isn’t thermally shocked by cold coolant while the combustion chamber above it is being fried by the hot returning coolant.
You’ll find that much of this stuff about more power from cold operating temps is just old wives tails and technically obsolete information from past generations.
|10-03-2012 06:17 PM|
|xzero117||I stand corrected, guess i got my definition of operating temperature wrong|
|10-03-2012 06:10 PM|
your operating temp is dictated by your thermostat UNLESS your cooling system isn't sufficient.
|10-03-2012 05:32 PM|
The Operatin' Temp, is Determined by the T-stat....
|10-03-2012 04:30 PM|
I mean running a thermostat is optional, but if you try turning your engine on without a thermostat on a sub 70 degree day, you're gonna have a bad time.
|10-03-2012 04:22 PM|
With your thinking or lack there of.
Why do we need a thermostat at all?
|10-03-2012 04:04 PM|
your engine will reach its operating temperature eventually no matter what the thermostat is
with a cooler thermostat it will simply take a bit longer to reach that point
|10-03-2012 02:19 PM|
I ran a 160, okay on a hot day but a cold night will kill driveability.
180 is the better choice, the motor needs some heat in it.
|10-03-2012 01:44 PM|
Of course if your engine is built to run at 160 or even cooler you can mitigate the wear and oil problems.
|10-03-2012 01:06 PM|
160 v 180 Thermostat
ASSUMING that the cooling system has the heat rejection capacity to pull the coolant temp down to 160 degrees or less, what would be the advantages/disadvantages of a 160 versus a 180 thermostat?
Thanks in advance.