Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Timing woes
User Name
lost password?   |   register now

Thread: Timing woes Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-06-2012 12:56 AM
cobalt327 "Roundy-round" = circle track.

Be sure the timing tab/damper line is really showing you true TDC. Info on the different timing tabs/damper lines is here. Info on determining TDC is here.

That cam is not so big that the timing needs to be locked at full advance. Won't hurt if it's race-only, but if you drive it on the street much you can use an advance curve. If you go to a smaller cam, or want better street manners, I agree to use a dual plane like the RPM.

Good luck.
10-05-2012 09:29 AM
Custom10 "roundy round cam" sorry but I am unwise to this terminology, what is that?

Changing to a dual plane RPM intake may help but with 210 runners you are already losing some abillity for lower RPM throttle responce. yes the vic junior is a good choice for WOT. Sounds like this combo needs gears, what is the rear gear ratio?
10-04-2012 10:15 PM
vinniekq2 the cam is not likely a roundyround cam with 112 you know what the icl of the cam is? Carb might need a little help with accellerator pump. More info is needed? what rpm are you mashing the throttle and what gear are you driving in at that time?
10-04-2012 04:42 PM
Timing woes

Allright then, I have an 84 monte carlo ss, sbc 350. Components are as follows

Crane blue racer
488/510 lift 234/244 druration @ .50 300 total lobe sep 112
eagle cylinder heads 2.10/1.60 valves 210 runners
edel victor junior intake
edel 750 #1407

this info given to me by previous owner.
It had an HEI dizzy, I have swapped out with MSD pro billet dizzy, 6AL box, and ss coil. Ignition timing locked set and set to 38*. 1434 jets with 1456 rods, 1432 sec. set 1 stage rich according to edel calibration specs. Cars does great with wot, but at cruise its fine until you mash throttle then hesistates, then grabs and goes. I am looking for a good throttle response theough the RPM range. I think this cam is a roundy round cam or something in that ballpark, I was looking for a lil input on switching cams and what would work best and advice would be greatly appreciated!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 06:47 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.