Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> engine choice 31 Ford sport coupe
User Name
Password
lost password?   |   register now

Thread: engine choice 31 Ford sport coupe Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-05-2012 08:08 AM
AutoGear Modular motors are very wide; something to think about.

I don't know what your mechanical prowess is, but if you want EFI, there was a Ford coupe with a 'Coyote' 5L in it, built by one of the california rod shops.

It looked very cool but probably cost a kings ransom.
10-05-2012 08:03 AM
ptribbey Thanks IC and Mr P. I know they will fit, as my friends have done it. What I should have been more clear on is a late model 302, say 2000 or up. They are lighter and a little smaller than the modulars? From what I,ve been reading, there should be no problem wringing 300 hp out of a 5.0. It would seem the modulars are more plentiful and cheaper up here in N WI. Hard to make a choice. Right now I have the rails deriveted, boxing plates ready to be tigged, 63 T-Bird 9" rear narrowed to 56". Getting a triangular 4 link from Paul Hortons. The front has not been ordered yet, but it will be the Heidts superride.
Pros and cons - 5.0 vs Modular?
10-05-2012 07:54 AM
ptribbey Thanks IC and Mr P. I know they will fit, as my friends have done it. What I should have been more clear on is a late model 302, say 2000 or up. They are lighter and a little smaller than the modulars? From what I,ve been reading, there should be no problem wringing 300 hp out of a 5.0. It would seem the modulars are more plentiful and cheaper up here in N WI. Hard to make a choice. Right now I have the rails deriveted, boxing plates ready to be tigged, 63 T-Bird 9" rear narrowed to 56". Getting a triangular 4 link from Paul Hortons. The front has not been ordered yet, but it will be the Heidts superride.
Pros and cons - 5.0 vs Modular?
10-05-2012 07:00 AM
Mr. P-Body Agreed, SBF is not a bad choice. Good engine. LOTS of "goodies".

The two "coolest" street rods I've seen in years had a different "Fords"... One was a '32 CHEVY "5-window coupe" in a club full of '32 FORDS, all with SBC engines. It had a Cleveland in it... It's name? "Bad Attitude"... I LOVED it!

The other was more of a "rat rod" (before they were "cool"). It was a T-bucket with a 300 6 cylinder. Sounded a lot like an airplane... Drew a LOT of attention.

While the Windsor "family" is more plentiful (260s, 289s, 302s are also "Windsor" engines), the Cleveland is the ONE. For a small block, it's pretty hard to argue with the look, the power and the "cool factor". There are still MANY out there, and new performance parts are readily available through all "regular" sources.

Or, you could always go the "never send a boy to do a MAN'S job" approach. 460s are plentiful and relatively cheap. No other Ford engine has more potential, possible excdeption, 427.

Just some ideas.

Jim
10-05-2012 06:16 AM
Irelands child
Quote:
Originally Posted by BOBCRMAN@aol.com View Post
Small block Ford engines do not fit well in Model A Fords. They are too long.
Bull pucky!!!!! These kinds of statements are 1960's true, prior to different length water pumps, oil pans and headers, etc

SB Fords are actually 27 inches long vs the Chevy almost 28 (27.88 to be exact*) and are both 22" wide.

There is NOTHING difficult about fitting a SB Ford in an 'A' chassis. This is mine - zip, zero, nada problem fitting it in place - and it is ~2 inches set back - my choice to keep tho a TCI error. Complete with LONG water pump, 29" long plus had I wanted to go that way, enough room for a mechanical fan:












Popular American V8 Engine Dimensions plus Ford Performance Parts 2012 catalog
10-05-2012 05:04 AM
BOBCRMAN@aol.com Small block Ford engines do not fit well in Model A Fords. They are too long.
10-05-2012 12:42 AM
ptribbey
engine choice 31 Ford sport coupe

Trying to decide what engine to run in my daily driver A sport coupe. At first I was thinking 4.6 police interceptor, or maybe a 5.4. Now im looking into a 5.0. I am targeting 300 hp. Ford is a must, Ease of parts availability is a plus . Maybe a mild cam(s), headers, dual 3", k&n, chip, nothing too serious. AOD trans and probably somewhere around 3.55 gears with a trac-loc. Any relevent opinions appreciated. Thanks, Paul

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:07 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.