Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Looking for a quicky
User Name
Password
lost password?   |   register now

Thread: Looking for a quicky Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-07-2012 10:35 AM
T-bucket23 2000 lb car with a sbc and a 671. You wont need to worry about how fast it winds up. lol
Whatever you build just be sure the compression ratio and piston type are blower friendly.
My 1700LB t-bucket with a 142 blower winds up real fast and is a hand full.
10-06-2012 10:09 PM
DOUGIEB59 GEE- THAT WILL BE TOO BAD!!!
10-06-2012 07:57 PM
vinniekq2 it will make mote than 500hp
10-06-2012 07:17 PM
DOUGIEB59
cam specs

i jus looked at the box... comp cams roller hydraulic lifters...
adv duration @ 286 both int/exh
@50 degrees- 230 both intake and exhaust
110 lobe seperation
w 586 lift int/exh
have roller rockers @ 1.6 ratio so should have plenty of air

never ran blower before...
thinking 1:1 ratio, looking for 6-8# boost

should push 500 hp?
10-06-2012 08:33 AM
ap72
Quote:
Originally Posted by techinspector1 View Post
Naturally aspirated, I agree you need more static compression ratio with a big lumpy cam. With a blower though, you need to reduce the SCR to prevent detonation and still run the big lumpy cam. Here's a recommendation from Blower Drive Service.....
Blower Drive Service: We Deliver Horse Power! - Blower Drive Systems, Blower Kits, Blower Cams, Custom Carb Service
yea, I forgot the blower part- my mistake.

For good power with a blower you'll want a smaller cam than NA, with a slightly wider LSA. A "big lumpy cam" may just result in a lot of fuel consumption and heat rather than power.
10-06-2012 03:18 AM
techinspector1
Quote:
Originally Posted by ap72 View Post
You're going to want more compression, at least 10:1 if you have a "big lumpy cam". 6500 RPM is EASY for just about any sbc as long as its well balanced and assembled. Your VALVETRAIN is critical though, if you're not worried about power go with a very mild solid cam, with beehive springs and you should be able to run stock rockers and valves.
Naturally aspirated, I agree you need more static compression ratio with a big lumpy cam. With a blower though, you need to reduce the SCR to prevent detonation and still run the big lumpy cam. Here's a recommendation from Blower Drive Service.....
Blower Drive Service: We Deliver Horse Power! - Blower Drive Systems, Blower Kits, Blower Cams, Custom Carb Service
10-06-2012 03:13 AM
techinspector1
Quote:
Originally Posted by ssmonty View Post
7.5-8:11 CR would be a good compression to shoot for if your using a blower.
Forged pistons are a very good idea. You'll also want to get a cam designed for use with a blower, as they generaly have a wider LSA.
You ought to do some research on the torque capacity of the Jag rear end you have. I can't say from experiance, but from what I've read and heard, putting one behind a blown motor may not be a good idea. Jag engines are not really known for producing high torque.
FWIW
ssmonty
I agree with the 7.5:1 to 8.0:1 static compression ratio with a blower. That will allow you to push 8 lbs of boost into the motor on pump gas. I see the cam LSA differently though. Blower Drive Service says you can use a wider LSA on ALCOHOL, but 110 works best on gasoline.
10-05-2012 11:15 PM
vinniekq2 Im back,,, If you build a blown,stroker small block of 377/391 range you could get 750 plus horse power using a 671 blower /roller cam and 195 heads. your throttle response will be instant. The car will scare the pants off ya.
lets go over the parts list you need/want. you can make 450 hp with out the blower,,,, post or PM the cam specs and what you have and lets shred some tires,,,seriously a blown big bore small block in a car weighing 2000 pounds will break the tires loose at 60 mph just by dipping deep into the throttle.
10-05-2012 07:52 PM
ssmonty 7.5-8:11 CR would be a good compression to shoot for if your using a blower.
Forged pistons are a very good idea. You'll also want to get a cam designed for use with a blower, as they generaly have a wider LSA.
You ought to do some research on the torque capacity of the Jag rear end you have. I can't say from experiance, but from what I've read and heard, putting one behind a blown motor may not be a good idea. Jag engines are not really known for producing high torque.
FWIW
ssmonty
10-05-2012 07:08 PM
ap72
Quote:
Originally Posted by Richiehd View Post
327, .030. Scat 6.125 Rods, Forged 350 pistons. Forged crank if you can afford it. Solid cam. Killer street hi reving street motor.
At only 6500rpm a 3.75" stroke will live just fine. and if you're going short stroke you may as well go for the 3" stroke with a 6.250" rod- but the rest of your engine will be QUITE expensive.
10-05-2012 06:44 PM
Richiehd 327, .030. Scat 6.125 Rods, Forged 350 pistons. Forged crank if you can afford it. Solid cam. Killer street hi reving street motor.
10-05-2012 05:38 PM
ap72
Quote:
Originally Posted by DOUGIEB59 View Post
Cam specs, i'm not positive... Card is at home, i know its a lumpy comp cam set up w roller lifters... Looking at some 195-ish heads... 8-8.5 compression ratio i think... Only looking to push to mid to hi 400 h/p range... I want a toy, not a death machine... D/b
I JUST WANT IT TO WIND UP LIKE A BANSHEE... GO LIKE HELL TO ABOUT 85-90 MPH AND THEN IM GONNA "CHICKEN OUT"... DONT NEED ANY NEW FRIENDS IN BLUE UNIFORMS...
You're going to want more compression, at least 10:1 if you have a "big lumpy cam". 6500 RPM is EASY for just about any sbc as long as its well balanced and assembled. Your VALVETRAIN is critical though, if you're not worried about power go with a very mild solid cam, with beehive springs and you should be able to run stock rockers and valves.
10-05-2012 04:53 PM
DOUGIEB59 Cam specs, i'm not positive... Card is at home, i know its a lumpy comp cam set up w roller lifters... Looking at some 195-ish heads... 8-8.5 compression ratio i think... Only looking to push to mid to hi 400 h/p range... I want a toy, not a death machine... D/b
I JUST WANT IT TO WIND UP LIKE A BANSHEE... GO LIKE HELL TO ABOUT 85-90 MPH AND THEN IM GONNA "CHICKEN OUT"... DONT NEED ANY NEW FRIENDS IN BLUE UNIFORMS...
10-05-2012 04:06 PM
against all odds 2 Holes:

1) i would build the car first then worry about the engine.

2) a stock 305/350 that has been balanced and blueprinted should be able to spin 6500 rpm with no problems, reach that rpm fairly quickly, and enjoy doing it.

This is the cheapest way.

3) If the car is going to be under 2000lbs., you don't need to worry about any "supposed' low-end torque problems.
10-05-2012 02:56 PM
vinniekq2 great idea. maybe elaborate on the camshaft? are you using the blower? heads dont flow RPM per se,they flow cfm and the cam duration gives the heads "time" to flow and valve lift working with heads will determine a total possible flow of air.how much power do you really need in that car? are you looking for the power to be linear? what size carb(s) are you using?
are you using a stock GM block? if so,2 bolt or 4? what CR will you use?
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.