Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Pistons dont fit in block.
User Name
Password
lost password?   |   register now

Thread: Pistons dont fit in block. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-28-2013 09:10 AM
prumora1 just like other post stated you need to file fit the rings, unless they are gapless, there should be a paper with your rings that give you the equation for figuring on your gap. it will have a multiplier for different applications such as street, racing, supercharged and even your types of fuel you plan to use.
all of these things make a difference when your putting your motor together. also there is a top and bottom to the rings, the top will be indicated by either a dot or a taper on the ring its self
02-27-2013 08:38 PM
tboneb4a i seen this thread is a bit old but if ur tryin to put them in a 350 it not gonna work thats a 4.00 inch bore. l2477 pistons are for a 400 small block whitch has a standard bore of 4.125 hope that helps ya out.
10-07-2012 08:32 PM
Silver Surfer It is probably worth mentioning that you need to ream the ridge off the top of the cylinders. If you put new rings on and leave the ridge, it will break the new rings.
10-07-2012 07:48 PM
cdminter59
Pistons don't fit block. Help

Quote:
Originally Posted by darce View Post
so what rings would you guys recommend??
Check your piston on the inside for a number. Call Hastings or Speed Pro with the number. They will tell you the correct ring part number. Is the number #10128249, and have 6106 on it? If it does it uses Hastings #5615.
10-07-2012 06:04 PM
BOBCRMAN@aol.com Sealed Power, Hastings, Perfect Circle, Mahle, are all quality stuff. Cast iron for best results in your situation.
10-07-2012 05:54 PM
darce so what rings would you guys recommend??
10-07-2012 04:31 PM
BOBCRMAN@aol.com No, cast rings are very forgiving. Thats why they are used in worn bores. Never Chrome or Moly!
10-07-2012 12:50 PM
darce ok guys so i decided to go with cast iron rings. would i need to re hone the cylinders?
10-07-2012 10:02 AM
CNC BLOCKS NE
Quote:
Originally Posted by bobcrman@aol.com View Post
251k rings will not fit gm factory pistons. Factory pistons require a "shallow groove" ring. Consult an automotive machine shop or real auto parts store for correct cast iron ring set for the different vin codes.
x2 !!!!!!!!!!!!!!
10-07-2012 07:46 AM
BOBCRMAN@aol.com 251k rings will not fit GM factory pistons. Factory pistons require a "Shallow groove" ring. Consult an automotive machine shop or REAL auto parts store for correct cast iron ring set for the different VIN codes.
10-07-2012 06:16 AM
Irelands child Most after market piston rings are 'file to fit'. To say that, they are manufactured .015 to .020 oversize to fit differences in the way each cylinder is bored.

I don't have photos handy, but you take each cylinder individually and each piston (I use that cylinders piston) and a set of the three rings that you intend on using in that cylinder. I then push the top two, one at a time, about an inch into the piston bore, using the top of the inverted piston itself and measure the end clearance with a feeler gauge. This should end up being be.005/.007 per inch of piston diameter(4" piston would be .020 gap) for the top two rings AFTER YOU FILE TO SIZE. This may entail several 'trips' into that cylinder and several passes with a file or special filer tool (Summit and others will have that tool). The bottom and usually 3 piece ring doesn't get any fitting (normally) and is installed as supplied.

There are many write ups on the internet, but if you have conventional cast/moly rings, will all use this kind of assembly. There are other kinds that are installed differently, but are specials with those 'special' high buck prices.

Dave W
10-07-2012 05:13 AM
poncho62 Sounds like your rings are too large....Try a ring in the bore by itself, without piston and see what the gap is at the end of it
10-07-2012 02:05 AM
darce
Pistons dont fit in block.

Hello i decided to re ring my chevy 350. I honed the cylinders with 400grit stones and bought new sealed power moly rings ze251k, now i tried to install the pistons in the block but couldnt. i bought the piston ring compressor and applied light oil to both the piston skirts and cylinders.

I noticed that piston stopped at the second compression ring. I hit it alittle hard and forced all the piston in but stopped, i didnt want to break anything. I then decided to pull the piston out. now there is a grey mark on the cylinder wall were the piston rings were.

I made sure i had boots on the bolts and not hitting the crankshaft. Also i made sure the rod wasnt hitting anywhere. And there was plenty of oil on these parts.

Help is really appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.