Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Three hole carb spacers?
User Name
Password
lost password?   |   register now

Thread: Three hole carb spacers? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-10-2012 01:41 AM
vinniekq2 I have never done any dyno testing of 3 hole spacers.We did do a few pulls with different 4 hole spacers and open spacers.remember when nascar use a spacer/restricter? The 4 hole spacer that has has porting done sometimes adds power.what I will try to describe is:
looking through the top of the spacer you see 4 holes with a flat bridge between the holes.Under side looking up you see the center cross has been ported to a point like a bullet shape. we tested same thing with all 4 holes chamfered and spacers with no dividers. The particular engine we were testing liked having the bullet nose cross the best.
some intakes are available with an inverted bullet on the intake floor.It does not work in every situation.

Like tech said,every engine has a different need
10-10-2012 12:34 AM
techinspector1
Quote:
Originally Posted by xxllmm4 View Post
Hey everyone, I was just thinking. Why don't you see any three hole carb spacers? Seems like it would be the best of both worlds. I have herd a few people have done it themselves but I have never seen any dyno charts or comparisons.
I'm at a loss to see any advantage. On a spread bore like you are showing, the motor runs all the time on the two primaries, which are the little bores at the front. When you mat the loud pedal, the larger secondaries kick in, both at the same time. I see no advantage in cutting out the wall between the secondaries. They're gonna flow the same, no matter whether there is a wall between the bores or whether there isn't. The only way you could make a difference is like timothale said, with a Holley 3-barrel because one long oval throttle plate has more area than two round ones like a Quadrajet.

Speaking of spacers, there is no arithmetical formula for making them work. Each motor is a combination unto itself and what works on one motor will not necessarily work on another motor.
10-09-2012 08:23 PM
timothale
3 barrel holly

I had an old 3 barrel holly, they were good for 5ooo rpm and above. I think it was rated over 1000 cfm I just used it for parts.
10-09-2012 08:17 PM
xxllmm4
Three hole carb spacers?

Hey everyone,

I was just thinking. Why don't you see any three hole carb spacers? Seems like it would be the best of both worlds. I have herd a few people have done it themselves but I have never seen any dyno charts or comparisons.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.