Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Vacuum Question
User Name
Password
lost password?   |   register now

Thread: Vacuum Question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-13-2012 08:28 PM
bigdog7373 Since the engine runs better with it getting more air then you need to check your idle mixture. Sounds like it's rich. What's your timing at?
10-13-2012 11:49 AM
cobalt327
Quote:
Originally Posted by pukas84 View Post
I have a small block Chevy with a demon carb. I Have the vacuum tank hose, trans modulator hose and brake booster hose going to a connector screwed into the back of the manifold. Idle is a little rough. I was messing with my car yesterday and forgot to plug the modulator hose in and the engine was running smooth. When I plugged the modulator back the idle was rough again. Any suggestions on why this happens? Mahalos.
What is the initial timing set at? What's the cam specs?

Might be pointing to the idle circuit being too rich. The added air from the open modulator fitting leaned it back out and the idle smoothed out. Have you adjusted the idle mixture screws to the highest vacuum/idle speed? Is the curb idle screw adjusted so far in that the idle mixture screws don't do anything (or very little) when the screws are turned in or out?
10-13-2012 09:01 AM
timothale
air leak,

Is the Modulator good, sounds like the diaphram is leaking and too much air getting into the intake. A hand pump vacuum tester is handy to have , I have seen guys suck on the tube to see if it holds vacuum, not aa me, if the modulator hose is long enough, run the engine, pinch the hose so it won't leak, pull of the hose put your finger on the end . unkink the hose and you should feel some vacuum in the hose. ,a lot of times a leaking modulator will allow oil to get into the hose..
10-12-2012 11:34 PM
pukas84
Vacuum Question

I have a small block Chevy with a demon carb. I Have the vacuum tank hose, trans modulator hose and brake booster hose going to a connector screwed into the back of the manifold. Idle is a little rough. I was messing with my car yesterday and forgot to plug the modulator hose in and the engine was running smooth. When I plugged the modulator back the idle was rough again. Any suggestions on why this happens? Mahalos.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:57 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.